Forum: Model A (1928-31)
Yesterday, 09:52 AM
|
|
Replies: 3
Views: 308
|
|
Forum: Model A (1928-31)
05-06-2024, 09:02 AM
|
|
Replies: 34
Views: 2,447
|
|
Forum: Model A (1928-31)
05-06-2024, 09:00 AM
|
|
Replies: 10
Views: 435
|
|
Forum: Model A (1928-31)
05-06-2024, 08:55 AM
|
|
Replies: 20
Views: 977
|
|
Forum: Model A (1928-31)
05-06-2024, 08:44 AM
|
|
Replies: 31
Views: 3,846
Re: Tillotson carb
The tillotson and marvel carburetor are better carburetors by design than the zenith the model A. runs much better with them!
|
|
Forum: Model A (1928-31)
05-05-2024, 08:11 AM
|
|
Replies: 3
Views: 308
|
|
Forum: Model A (1928-31)
05-04-2024, 12:17 PM
|
|
Replies: 17
Views: 796
Re: Removing stuck distributor and lower shaft
Great news that you got it out now rebuild it with the 2 pc setup the reason they used a 2 pc setup is to allow for slight misalignment with the 1 pc shaft that slight misalignment puts stress on the...
|
|
Forum: Model A (1928-31)
05-04-2024, 12:11 PM
|
|
Replies: 13
Views: 670
|
|
Forum: Model A (1928-31)
04-30-2024, 06:31 AM
|
|
Replies: 20
Views: 2,817
|
|
Forum: Model A (1928-31)
04-30-2024, 06:15 AM
|
|
Replies: 14
Views: 948
Re: Little Dearborn
They were the source where I purchased my front bumper for my 1928 roadster pickup I wonder who's making the bumpers today?
|
|
Forum: Model A (1928-31)
04-29-2024, 11:51 AM
|
|
Replies: 8
Views: 688
|
|
Forum: Model A (1928-31)
04-29-2024, 11:22 AM
|
|
Replies: 21
Views: 1,067
|
|
Forum: Model A (1928-31)
04-28-2024, 11:40 AM
|
|
Replies: 13
Views: 1,163
|
|
Forum: Model A (1928-31)
04-28-2024, 11:15 AM
|
|
Replies: 4
Views: 512
|
|
Forum: Model A (1928-31)
04-24-2024, 10:56 AM
|
|
Replies: 10
Views: 969
Re: engine compression levels.
My engine has been sleeve back to the original bore size and has the original 4.2 compression head my compression readings are basically 60-65 on all 4 cylinders.
|
|
Forum: Model A (1928-31)
04-22-2024, 10:30 AM
|
|
Replies: 29
Views: 1,945
|
|
Forum: Model A (1928-31)
04-17-2024, 09:17 PM
|
|
Replies: 2
Views: 563
Re: Clutch Housing Crack
I have a crack in my AA four-speed bell housing. I carefully cleaned the housing, followed the end of the crack and drilled the hole to prevent it from spreading. I believe mine was probably cracked...
|
|
Forum: Model A (1928-31)
04-17-2024, 08:36 AM
|
|
Replies: 7
Views: 717
|
|
Forum: Model A (1928-31)
04-15-2024, 11:52 AM
|
|
Replies: 14
Views: 799
|
|
Forum: Model A (1928-31)
04-14-2024, 10:41 AM
|
|
Replies: 25
Views: 1,659
Re: Car will not start
My suggestion is that the gear has slipped just enough ° to drop the compression but still rotate it. If so it is begining to fail. 40psi is close to the point of no longer firing because of the...
|
|
Forum: Model A (1928-31)
04-14-2024, 10:26 AM
|
|
Replies: 17
Views: 995
|
|
Forum: Model A (1928-31)
04-14-2024, 10:14 AM
|
|
Replies: 14
Views: 799
Re: generator output
When taking your voltage readings at the battery terminals when the engines at an idle you should not see any output until just above an idle when the cutout actually closes.
|
|
Forum: Model A (1928-31)
04-12-2024, 10:32 AM
|
|
Replies: 25
Views: 1,659
Re: Car will not start
With that low of compression in each cylinder I'm beginning to wonder if the timing gear has slipped.
|
|
Forum: Model A (1928-31)
04-10-2024, 10:17 AM
|
|
Replies: 14
Views: 871
Re: Condenser Capacity
I had a condenser fail about a year ago. I replaced it with one of the burnout proof ones from Snyder's which I believe is an A&L condenser. I noticed the new condenser measured 19 micro Farads but...
|
|
Forum: Model A (1928-31)
04-10-2024, 09:56 AM
|
|
Replies: 35
Views: 2,854
|
