Forum: Model A (1928-31)
01-26-2017, 10:53 AM
|
Replies: 344
Views: 65,092
|
Forum: Model A (1928-31)
01-10-2017, 03:16 PM
|
Replies: 6
Views: 1,320
Welcome aboard
Model A guy goes to get on a bus. He is carrying a drive shaft. Driver says you can't get on here company will not allow any package over four feet and that is five feet. Model A guy goes into a...
|
Forum: Model-A
12-21-2016, 12:59 PM
|
Replies: 0
Views: 1,249
|
Forum: Model A (1928-31)
12-17-2016, 02:46 PM
|
Replies: 1
Views: 1,238
carburetor float valve
Rebuilding a tillotson carburetor.Looking for recommendations on what type of float valve to use. maybe a viton plastic tip? Whats recommended and where can I get one? Thank you
|
Forum: Model A (1928-31)
12-17-2016, 11:52 AM
|
Replies: 12
Views: 2,129
|
Forum: Model A (1928-31)
12-14-2016, 10:34 AM
|
Replies: 10
Views: 2,235
|
Forum: Model A (1928-31)
12-14-2016, 10:32 AM
|
Replies: 12
Views: 2,129
1931 shutoff grommet install
Any trick to installing the rubber grommet in the fire wall before installing the under hood shutoff valve.Its putting up a good fight and so far its winning.
|
Forum: Model A (1928-31)
11-22-2016, 09:28 AM
|
Replies: 10
Views: 2,109
Re: 31 AA - Gas Valve Rebuild Kit?
Don't know if my late 31 {on firewall under the hood] is original or repro. When the handle points to front of car valve is closed when it points to the passenger side valve is open.Is that an...
|
Forum: Model A (1928-31)
11-21-2016, 02:51 PM
|
Replies: 4
Views: 1,693
Late 1931 indented firewall gas valve
Looking for advice on my gas valve which has a slight leak when off. Brattons sells a replacement valve. They also sell a gas line which has a valve in the line, They have a fuel valve Stem which...
|
Forum: Model-A
11-15-2016, 12:44 PM
|
Replies: 6
Views: 1,655
|
Forum: Model-A
11-15-2016, 12:44 PM
|
Replies: 8
Views: 1,875
|
Forum: Model-A
11-15-2016, 12:43 PM
|
Replies: 3
Views: 1,281
|
Forum: Model-A
11-07-2016, 09:39 AM
|
Replies: 3
Views: 1,281
|
Forum: Model-A
11-07-2016, 09:39 AM
|
Replies: 8
Views: 1,875
|
Forum: Model-A
11-07-2016, 09:38 AM
|
Replies: 6
Views: 1,655
|
Forum: Model A (1928-31)
11-07-2016, 08:56 AM
|
Replies: 14
Views: 2,802
|
Forum: Model A (1928-31)
10-31-2016, 02:19 PM
|
Replies: 12
Views: 3,236
Tow tooth steering adjustment
Im working on adjusting my two tooth box.All is tight except when moving the pitman arm from front to back of car. I have about 1/8 inch play.This is in the box The bolt from pitman arm to shaft is...
|
Forum: Model A (1928-31)
10-27-2016, 09:37 AM
|
Replies: 41
Views: 19,481
|
Forum: Model A (1928-31)
10-23-2016, 10:12 AM
|
Replies: 124
Views: 36,465
Re: Our Model A wreck in Austin, TX
Synchro 909 has what I think is a good thought. After stoping at a red light I had a car come very close to hitting me. Im sure they saw me. Could it be that it did not dawn on them that I was a car?...
|
Forum: Model-A
10-23-2016, 09:45 AM
|
Replies: 6
Views: 1,655
|
Forum: Model-A
10-23-2016, 09:44 AM
|
Replies: 8
Views: 1,875
|
Forum: Model-A
10-23-2016, 09:43 AM
|
Replies: 3
Views: 1,281
|
Forum: Model A (1928-31)
10-23-2016, 09:40 AM
|
Replies: 8
Views: 2,030
|
Forum: Model A (1928-31)
10-22-2016, 02:17 PM
|
Replies: 8
Views: 2,030
1931 Gas valve removal
Planning on removing the under hood gas valve on my 1931 and polish the seat to stop some seepage. Can I just unscrew it from the engine side or is it necessary for someone to hold it under the gas...
|
Forum: Model A (1928-31)
10-22-2016, 07:31 AM
|
Replies: 4
Views: 1,186
|