Forum: Early V8 (1932-53)
01-28-2024, 05:09 PM
|
Replies: 11
Views: 945
Re: Ultra Sonic Cleaner
I have used cartridge brass cleaner and water mixed about the same dilution as cleaning brass. I'm going to try Simple Green as it might be faster.
|
Forum: Early V8
01-25-2024, 07:34 PM
|
Replies: 0
Views: 195
WTB holley 94 parts
I need the center body ( jets and accelerator pump located ) for a pre 8ba 94 in good condition. Model 91-29, 91-99, or 59. One of the jet well plugs is stripped and not correctly repaired. This is...
|
Forum: Early V8 (1932-53)
11-13-2023, 05:10 PM
|
Replies: 15
Views: 1,393
|
Forum: Early V8 (1932-53)
10-11-2023, 04:53 AM
|
Replies: 25
Views: 1,297
Re: radiator fan 40/41 pickup ID
That looks like a good alternative @19Fordy. I need to get the cab in place so I can see what needs to move. I may get there by spring .
|
Forum: Early V8 (1932-53)
10-10-2023, 05:15 PM
|
Replies: 25
Views: 1,297
Re: radiator fan 40/41 pickup ID
I have the sheilds and I'll use them when I get to final assembly. I have a lot of body work to go yet. I am using the chassis for a "run stand"and a place to store the the engine and transmission.
|
Forum: Early V8 (1932-53)
10-10-2023, 05:08 PM
|
Replies: 25
Views: 1,297
|
Forum: Early V8 (1932-53)
10-09-2023, 03:36 PM
|
Replies: 25
Views: 1,297
|
Forum: Early V8 (1932-53)
10-09-2023, 03:33 PM
|
Replies: 25
Views: 1,297
Re: radiator fan 40/41 pickup ID
Thanks to everyone who commented. I should have looked at the fan closer before installing it. I probably needed to trim the hoses anyway. New hoses are on the way and I picked up antifreeze today...
|
Forum: Early V8 (1932-53)
10-09-2023, 03:26 PM
|
Replies: 25
Views: 1,297
Re: radiator fan 40/41 pickup ID
Let me catch up. I trimmed about 5/16 in. off the long end of the hoses ans re-installed the trimmed ends on the pumps as Kube suggested. I laid the fan face down on a flat surface and found some of...
|
Forum: Early V8 (1932-53)
10-09-2023, 09:04 AM
|
Replies: 25
Views: 1,297
Re: radiator fan 40/41 pickup ID
Thanks, Kube. I installed the hoses with the long end on the pump to clear an aftermarket sway bar. I have almost an inch between the fan and radiator core; I am thinking about making a 1/4 in....
|
Forum: Early V8 (1932-53)
10-08-2023, 03:54 PM
|
Replies: 25
Views: 1,297
radiator fan 40/41 pickup ID
I just fired the 59A for the first time and it went pretty well except the crank mounted fan skinned the lower radiator hoses. This fan was on the engine in a '40 2dr sedan I bought so I assumed it...
|
Forum: Early V8 (1932-53)
09-04-2023, 08:44 AM
|
Replies: 18
Views: 1,388
|
Forum: Early V8 (1932-53)
09-03-2023, 02:54 PM
|
Replies: 18
Views: 1,388
|
Forum: Early V8 (1932-53)
09-02-2023, 06:39 PM
|
Replies: 18
Views: 1,388
|
Forum: Early V8
06-15-2023, 10:43 AM
|
Replies: 1
Views: 727
|
Forum: Early V8
04-04-2023, 12:14 PM
|
Replies: 1
Views: 727
2 piece truck oil pan 59AB
i want both parts of the 2 piece oil pan for a 59 AB engine . I believe it was a truck only. It allowed the clutch and flywheel to be changed with out removing the oil pan.
|
Forum: Early V8 (1932-53)
04-03-2023, 09:14 PM
|
Replies: 3
Views: 708
Re: Interesting Rear Axle Options...
I am using the 28 spline axles and the kit pieces in my 41 pickup with the "lincoln" brake backing plates (same kit as for the stock brakes) and the center section converted to open drive. The open...
|
Forum: Early V8 (1932-53)
03-29-2023, 04:51 AM
|
Replies: 10
Views: 2,452
|
Forum: Early V8 (1932-53)
03-27-2023, 04:49 PM
|
Replies: 10
Views: 2,452
|
Forum: Early V8 (1932-53)
03-27-2023, 09:40 AM
|
Replies: 10
Views: 2,452
|
Forum: Early V8 (1932-53)
03-27-2023, 09:32 AM
|
Replies: 10
Views: 2,452
Re: 59 AB head gasket orientation
Page one of install PDF:
https://edelbrock-instructions-v1.s3.amazonaws.com/edelbrock/1125.pdf
Sorry, I woke up late this morning. Joel
|
Forum: Early V8 (1932-53)
03-26-2023, 11:58 PM
|
Replies: 10
Views: 2,452
Re: 59 AB head gasket orientation
Thanks for the reply.On the Edlebrock site ,there is a picture of the gasket that implies the small holes are to the front with one circled . It says to use that hole as the location to drill the...
|
Forum: Early V8 (1932-53)
03-26-2023, 03:20 PM
|
Replies: 10
Views: 2,452
59 AB head gasket orientation
I have Best copper sandwich head gaskets . They are identical. each has some smaller water holes in one end of the gasket. The other end has holes the same size as the head. (edelbrock heads) my...
|
Forum: Early V8 (1932-53)
02-12-2023, 11:33 PM
|
Replies: 19
Views: 1,686
Re: 59 block oil relief plunger install
I seriously want to thank everyone for their replies . I think Kube's advice is what i'm going to do. I plan on cranking the engine over with the plugs out before I install it, so I'll know then if I...
|
Forum: Early V8 (1932-53)
02-12-2023, 11:24 PM
|
Replies: 19
Views: 1,686
Re: 59 block oil relief plunger install
On page 279 of Green book it shows 59A6600 A1 with the same relief spring in block relief as it does for the 59A-6600-A2 pump only the spring p/n is 8BA 6654.
This is why I think the helical gear...
|