Forum: Early V8
02-04-2024, 06:01 PM
|
Replies: 0
Views: 187
|
Forum: Model A (1928-31)
12-02-2023, 05:47 PM
|
Replies: 15
Views: 1,463
Brass fuel gauge float ?'s
I have been trying to order some brass floats from Reenlee Kotas for a couple of months. He is not returning my messages. I hope everything is alright with him. Anybody have contact with him recently?
|
Forum: Early V8 (1932-53)
12-02-2023, 05:17 PM
|
Replies: 5
Views: 690
Re: Holley 94 "EAB" question
I have been told the EAB code heads are more desirable due to an increase in compression ratio. Are there other parts I should be looking for also to help my 8BA run better?
|
Forum: Early V8 (1932-53)
12-01-2023, 10:28 PM
|
Replies: 5
Views: 690
Holley 94 "EAB" question
A friend showed me a 2x2 aluminum intake he has. There is an EAB cast code carb and an 8BA cast code carb. What years of cars had the EAB code?
|
Forum: Model A (1928-31)
11-23-2023, 11:06 PM
|
Replies: 17
Views: 2,241
Re: Zenith throttle plate modification
The first part of this post has been proven about the importance and effect of turbulence and atomizing the fuel/air mixture. Yes the edge of the throttle butterfly is beveled to, I believe, obtain...
|
Forum: Model A (1928-31)
11-22-2023, 10:22 AM
|
Replies: 19
Views: 2,023
Re: My Cardiologist
I drove my dad's '29 Sport Couple in a parade years ago and a heck of a lot younger. Told myself never again because of that. My brother did the same a few years later on a much shorter parade. He...
|
Forum: Early V8
11-19-2023, 09:38 AM
|
Replies: 0
Views: 148
1938 standard tudor sedan sheet metal
Set of 4 NOS fenders for a 1938 Ford Standard Tudor Sedan $2400.00 Also have 2 hoods priced at $850.00 and $600.00. The vertical stainless steel piece in the center of the grille NOS $450.00. Early...
|
Forum: Model A (1928-31)
11-12-2023, 09:42 PM
|
Replies: 11
Views: 1,002
Re: Patch Panels - Recommendations on quality
Check out Brookville Roadster in Brookville Ohio, I bought my rear of cab and rear cab corners, seat riser and complete box from them a few years back. Excellent quality and service. All parts were...
|
Forum: Early V8 (1932-53)
11-12-2023, 09:16 PM
|
Replies: 5
Views: 679
|
Forum: Early V8 (1932-53)
11-11-2023, 11:05 PM
|
Replies: 5
Views: 679
|
Forum: Model-A
10-24-2023, 07:18 PM
|
Replies: 0
Views: 544
|
Forum: Model A (1928-31)
10-15-2023, 09:56 AM
|
Replies: 11
Views: 998
Re: Assembly plant help decipher
When did the plant in Omaha Ne. start operation? Did Budd or Briggs make the non steel roof cabs? I wonder if that "B" or "8" is a B for Budd or Briggs.
|
Forum: Model A (1928-31)
10-15-2023, 09:54 AM
|
Replies: 11
Views: 998
Re: Assembly plant help decipher
Gary WA - The truck is titled as a 1931, it is a closed cab (not a steel roof) and the narrow wood floor box like the earlier pickups. I think the reasoning behind the 1931 title year is that is when...
|
Forum: Model A (1928-31)
10-14-2023, 02:39 PM
|
Replies: 11
Views: 998
Re: Assembly plant help decipher
Gary WA thanks, I visited his web site this morning and did not come up with a definitive answer to my question. He has done extensive research that is for sure.
|
Forum: Model A (1928-31)
10-14-2023, 01:48 PM
|
Replies: 11
Views: 998
Assembly plant help decipher
I have tried to look up the assembly plant information of my Model A pickup, by the frame rail number it is a September 22 1930 engine build date. On the body cross member the number is either a "B"...
|
Forum: Early V8 (1932-53)
08-07-2023, 04:27 PM
|
Replies: 112
Views: 8,243
|
Forum: Model-A
08-06-2023, 12:08 PM
|
Replies: 1
Views: 482
|
Forum: Model A (1928-31)
08-06-2023, 11:06 AM
|
Replies: 9
Views: 889
Re: Adjust toe-in
Here is some more specs. to chew on from the Service Bulletin dated Feb.1936 Toe-in set at 3/32" for the Model A. That is what I set mine at using a "do it yourself" device from TMR until I can get...
|
Forum: Model-A
07-16-2023, 02:00 PM
|
Replies: 1
Views: 408
|
Forum: Model-A
07-14-2023, 12:49 PM
|
Replies: 1
Views: 482
Marvel - Schibler carb.
Any interest in a Marvel Schibler carb. It was attached to an A engine I rescued from the scrap iron pile. I'm looking for a Model B distributor in restorable condition. Inquire with your cell number...
|
Forum: Model-A
07-03-2023, 06:57 PM
|
Replies: 1
Views: 408
FREE Model AA transmission with clutch housing
It has been claimed and I made a new Model A friend, win-win! I picked up this AA transmission with a 2 engine rescue the other day. It has parts on it I will never use and I hate to see it get...
|
Forum: Early V8 (1932-53)
04-29-2023, 09:45 AM
|
Replies: 32
Views: 3,468
Re: New Member - 1953 F100
Can we get some clear detail pictures of the front engine mount area please, I think I have the correct front bracket piece that goes between the cross member and the water pumps. And am not certain...
|
Forum: Model A (1928-31)
04-27-2023, 02:40 PM
|
Replies: 3
Views: 813
Ammeter source
Looking for a source for quality ammeters new or original.
|
Forum: Model A (1928-31)
02-08-2023, 10:29 PM
|
Replies: 1
Views: 611
Re: '30 A hood hinge pin length
I have done some research on here since putting up my first post. I found a post from Neil Wilson in Boulder CO. He is into AA's, and since my "A" is a pickup I took down some notes. Top hood hinge...
|
Forum: Model A (1928-31)
02-08-2023, 08:19 PM
|
Replies: 1
Views: 611
|