Forum: Late V8
10-14-2023, 07:05 AM
|
Replies: 0
Views: 674
|
Forum: Early V8 (1932-53)
04-16-2023, 04:38 PM
|
Replies: 40
Views: 8,729
Re: MA9 cap on Mallory YC
For people that may be searching just wanted to update this thread with the MA9 cap ($83.00) on a Mallory YC distributor. Exact replacement with the MA7 ($21.00) rotor.
|
Forum: Late V8
07-18-2022, 05:12 PM
|
Replies: 0
Views: 494
|
Forum: Early V8
06-29-2022, 05:28 AM
|
Replies: 1
Views: 358
|
Forum: Early V8
06-29-2022, 05:27 AM
|
Replies: 1
Views: 306
|
Forum: Early V8
06-29-2022, 05:27 AM
|
Replies: 1
Views: 304
|
Forum: Early V8
06-29-2022, 05:27 AM
|
Replies: 1
Views: 593
|
Forum: Early V8
06-24-2022, 06:31 AM
|
Replies: 1
Views: 593
1936 Ford Radiator
1936 Ford Radiator SOLD
About a year ago I had a local radiator shop fix a leak, and then ran this at low pressure on my 8ba test stand. So it doesn't leak.
Local pickup only
|
Forum: Early V8
06-18-2022, 08:55 PM
|
Replies: 0
Views: 275
|
Forum: Early V8
06-18-2022, 08:53 PM
|
Replies: 1
Views: 304
|
Forum: Early V8
06-18-2022, 08:42 PM
|
Replies: 1
Views: 306
|
Forum: Early V8
06-18-2022, 08:34 PM
|
Replies: 1
Views: 358
|
Forum: Early V8
06-18-2022, 08:32 PM
|
Replies: 0
Views: 314
|
Forum: Late V8
05-30-2022, 05:59 PM
|
Replies: 1
Views: 853
Re: 1963 ford falcon hardtop
New Moog front springs, upper and lower control arms, shocks and strut rod bushings. Also new Dayton USA made rear six leaf springs. Price increase is for parts only, the labor is FREE. Starting...
|
Forum: Late V8
04-17-2022, 10:27 AM
|
Replies: 1
Views: 853
1963 ford falcon hardtop
1963 Ford Falcon Futura - 260 V8 Auto. Starts, stops and yard drives - no exhaust.
Open Maryland title. Sub rails are solid, the trunk floor has holes. I just installed passenger side full length...
|
Forum: Early V8 (1932-53)
03-30-2022, 11:38 AM
|
Replies: 37
Views: 4,358
Re: Holley 94 on 8ba barely runs * Resolved *
After several hours of troubleshooting and research (here and elsewhere) I found the cause of my hesitation and lack of power. It was worn insulation on the hot wire under my breaker plate. I wasn't...
|
Forum: Early V8 (1932-53)
03-23-2022, 11:24 AM
|
Replies: 37
Views: 4,358
Re: Holley 94 on 8ba barely runs
Yes I'm using compressed air. I did check for leaks with carb clean and didn't notice any difference. Vacuum readings idling is almost 18" so if there's a leak its a very small one.
|
Forum: Early V8 (1932-53)
03-23-2022, 11:20 AM
|
Replies: 37
Views: 4,358
|
Forum: Early V8 (1932-53)
03-23-2022, 05:35 AM
|
Replies: 37
Views: 4,358
Re: Holley 94 on 8ba barely runs
I did what Charlie advised and when I draw on the vac can, the breaker plate moves a lot, and will stay there as long as I hold on the draw.
Ken, I just disassembled this carb and believe I'll...
|
Forum: Early V8 (1932-53)
03-21-2022, 07:56 PM
|
Replies: 37
Views: 4,358
|
Forum: Early V8 (1932-53)
03-20-2022, 05:58 PM
|
Replies: 37
Views: 4,358
Re: Holley 94 on 8ba barely runs
No flatjack9 I have it connected. Next chance I get, I'll reset it with the carb plugged.
I should add that I don't notice the timing dimple on the pulley going lower as I rev the engine. Maybe...
|
Forum: Early V8 (1932-53)
03-20-2022, 02:58 PM
|
Replies: 37
Views: 4,358
Re: Holley 94 on 8ba barely runs
After cleaning and reassembling the carburetor it will now idle. There's a stumble off idle and no power driving it around the yard. This is a model a project car, that gets backed out of the garage...
|
Forum: Early V8 (1932-53)
03-15-2022, 05:46 AM
|
Replies: 37
Views: 4,358
Re: Holley 94 on 8ba barely runs
I had a little time after work yesterday and checked my coil. I have 1 ohm resistance on the primary windings and 7.4K to the coil center. 12V on the negative going to the distributor, and my...
|
Forum: Early V8 (1932-53)
03-14-2022, 01:01 PM
|
Replies: 37
Views: 4,358
|
Forum: Early V8 (1932-53)
03-14-2022, 11:50 AM
|
Replies: 37
Views: 4,358
Re: Holley 94 on 8ba barely runs
Appreciate all the answers. I believe this carb is a 94 for an 8ba with the vacuum on the back of the carb to the dist. Not directly from the intake.
roto - I'm not sure of if the coil is a 1.5...
|