Forum: Model A (1928-31)
01-24-2024, 01:50 AM
|
Replies: 9
Views: 1,137
|
Forum: Model A (1928-31)
01-24-2024, 01:18 AM
|
Replies: 31
Views: 1,930
Re: Do rivet nuts work?
Seat Bolt should be very secure especially in a hot rod. I would go with flat bar stock like you're talking about, attach that to both ends of the body rail frame, drill and tap for truss head...
|
Forum: Model-A
01-13-2024, 03:37 AM
|
Replies: 12
Views: 3,198
Re: 1928 Tudor parts
I have everything on my list above EXCEPT a seat bar (pictured in the post above). I need at least one but will take 2 if you have them.
Need the seat bar ONLY, can't edit the older posts.
...
|
Forum: Early V8
01-06-2024, 07:27 PM
|
Replies: 0
Views: 141
1940 car/pickup park light bulb terminal
Looking for the bulb housing with the spring on the outside and inside intact for a 1940 car/pickup or 1941 pickup. It's the one that twists into the top of the bucket to light up the park lens. I...
|
Forum: Early V8 (1932-53)
12-01-2023, 10:00 PM
|
Replies: 5
Views: 625
|
Forum: Early V8 (1932-53)
11-27-2023, 01:55 AM
|
Replies: 5
Views: 625
1941 Ford P/U question
Dumb question time, the air deflectors on a '41 p/u (the ones to direct air into the radiator). Do the side ones bolt on the inside of the grille or in between the fender and the grille?
...
|
Forum: Model-A
11-18-2023, 12:59 AM
|
Replies: 12
Views: 3,198
Re: 1928 Tudor parts
Bump for a seat bar.
https://www.fordbarn.com/forum/attachment.php?attachmentid=503791&d=1669013669
|
Forum: Model-A
09-15-2023, 08:18 PM
|
Replies: 12
Views: 3,198
|
Forum: Early V8 (1932-53)
09-05-2023, 11:38 PM
|
Replies: 18
Views: 1,349
|
Forum: Model A (1928-31)
09-05-2023, 11:07 PM
|
Replies: 3
Views: 655
|
Forum: Early V8 (1932-53)
08-22-2023, 11:50 PM
|
Replies: 10
Views: 838
Re: tire balancing 1940 coupe
Bubble or spin or on the car balancer all work great if done properly. Only thing I can add would be to "static" balance it, so all the weights are of the inside of the wheel.
|
Forum: Model-A
08-18-2023, 02:46 PM
|
Replies: 12
Views: 3,198
|
Forum: Early V8 (1932-53)
08-14-2023, 02:02 PM
|
Replies: 15
Views: 1,620
Re: Hidden USB Charger
I bought a couple of chargers from a marine parts place and made a bracket under the dash.
https://www.jalopyjournal.com/forum/attachments/power-outlet-2-jpg.4023469/
|
Forum: Model-A
07-27-2023, 12:50 AM
|
Replies: 12
Views: 3,198
|
Forum: Model-A
05-23-2023, 12:33 AM
|
Replies: 12
Views: 3,198
|
Forum: Model A (1928-31)
05-06-2023, 07:27 PM
|
Replies: 17
Views: 3,196
|
Forum: Early V8 (1932-53)
03-05-2023, 06:28 PM
|
Replies: 17
Views: 2,552
|
Forum: Early V8 (1932-53)
02-26-2023, 04:58 AM
|
Replies: 12
Views: 866
Re: tube shocks
I used an old clamp on kit in the rear. The KYBs went to my old '54 panel as they were too stiff for the '47. I know the angle is steep, but the exhaust is in the way.
|
Forum: Early V8 (1932-53)
02-26-2023, 04:53 AM
|
Replies: 12
Views: 866
Re: tube shocks
Did my '47 through the axle like a '48, go slow and use lots of cutting oil. I've seen the kits to add it on the perch pin, but I've also seen a few with broken off ears.
|
Forum: Model A (1928-31)
02-26-2023, 04:42 AM
|
Replies: 17
Views: 3,196
|
Forum: Model-A
02-26-2023, 04:37 AM
|
Replies: 12
Views: 3,198
|
Forum: Model-A
12-30-2022, 10:53 PM
|
Replies: 12
Views: 3,198
|
Forum: Model-A
12-05-2022, 01:01 AM
|
Replies: 12
Views: 3,198
|
Forum: Early V8 (1932-53)
11-28-2022, 09:44 PM
|
Replies: 8
Views: 1,199
|
Forum: Early V8 (1932-53)
11-28-2022, 09:37 PM
|
Replies: 7
Views: 752
Re: 40-41 rear pickup window gasket
I also used Dennis Carpenter for front and rear glass, fit perfectly. Front was a pain and took LOTS of soap.
I did it in 2020 if I remember correctly.
|