Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 37
Search took 0.00 seconds.
Search: Posts Made By: FlatAddict
Forum: Model-A 10-10-2013, 09:24 PM
Replies: 5
Views: 3,506
Posted By FlatAddict
Forum: Model-A 10-06-2013, 04:54 PM
Replies: 5
Views: 3,506
Posted By FlatAddict
Re: 1930 Ford Model A 5 Window Coupe

No title at this point.

bump
Forum: Model-A 10-02-2013, 10:01 PM
Replies: 5
Views: 3,506
Posted By FlatAddict
Forum: Model-A 09-30-2013, 05:47 AM
Replies: 5
Views: 3,506
Posted By FlatAddict
Re: 1930 Ford Model A 5 Window Coupe

Panel above trunk lid for a 28'-29' coupe or sport coupe. Good and solid, flanges need a little luvin.
$60.00
Forum: Model-A 09-30-2013, 05:44 AM
Replies: 5
Views: 3,506
Posted By FlatAddict
1930 Ford Model A 5 Window Coupe

For sale is a 1930 Ford Model Five Window Coupe. The body is rough but salvageable. It is a rumble lid coupe. The chassis and engine were restored at some point in the past. The body is one I had and...
Forum: Early V8 03-24-2012, 07:30 AM
Replies: 6
Views: 2,741
Posted By FlatAddict
Re: 1939 Ford Coupe

up, up, up
Forum: Early V8 03-09-2012, 09:21 PM
Replies: 6
Views: 2,741
Posted By FlatAddict
Forum: Early V8 02-27-2012, 10:17 PM
Replies: 6
Views: 2,741
Posted By FlatAddict
Re: 1939 Ford Coupe

Call Jerry, make an offer.
Forum: Early V8 02-22-2012, 11:50 PM
Replies: 6
Views: 2,741
Posted By FlatAddict
Forum: Early V8 02-17-2012, 07:25 AM
Replies: 6
Views: 2,741
Posted By FlatAddict
Forum: Early V8 (1932-53) 02-11-2012, 08:55 PM
Replies: 4
Views: 1,442
Posted By FlatAddict
Flathead Questions?

1. Will a dual carb 255 Merc Flathead run on 6 volt? or at least fire or sputter?

2. Will a dual carbed 255 Merc Flathead running 6 volt produce a low compression number?:)
Forum: Early V8 02-10-2012, 10:26 PM
Replies: 6
Views: 2,741
Posted By FlatAddict
Re: 1939 Ford Coupe

More pictures
Forum: Early V8 02-10-2012, 10:24 PM
Replies: 6
Views: 2,741
Posted By FlatAddict
1939 Ford Coupe

1939 Ford Coupe. 350/350 combo, about 400hp. Listing this for a friend so give him a call for more info. His name is Jerry. Cell: 406.263.4409 or at home: 406.228.9044
Forum: Model-A 01-21-2012, 10:16 PM
Replies: 0
Views: 926
Posted By FlatAddict
28'-29' 1/4 Window Garnish Moulding A Coupe

Interior Quarter Window Garnish Moulding for a 28'-29' Ford Model A Coupe. I think it is passenger side. Surface rust, some pitting but no holes or rust through. $60.00 shipped in lower 48 will trade...
Forum: Model-A 06-03-2011, 06:16 AM
Replies: 16
Views: 3,610
Posted By FlatAddict
Forum: Model-A 05-30-2011, 09:41 PM
Replies: 16
Views: 3,610
Posted By FlatAddict
Forum: Model-A 05-27-2011, 08:32 PM
Replies: 16
Views: 3,610
Posted By FlatAddict
Forum: Model-A 05-23-2011, 10:22 PM
Replies: 16
Views: 3,610
Posted By FlatAddict
Forum: Model-A 05-18-2011, 09:10 PM
Replies: 16
Views: 3,610
Posted By FlatAddict
Forum: Model-A 05-15-2011, 09:02 AM
Replies: 16
Views: 3,610
Posted By FlatAddict
Forum: Model-A 05-11-2011, 10:07 PM
Replies: 16
Views: 3,610
Posted By FlatAddict
Re: Original Model A Parts $20 under

Don't mean to early bump just need to add stuff.
1. Oil Filler Tube $3.00
2. Shift Tower for a 30' AA 4spd $20.00
3. Brake Shoe Cores $10.00 for all. (SOLD)
4. Sport Coupe Top Iron $20.00
5....
Forum: Model-A 05-10-2011, 10:08 PM
Replies: 16
Views: 3,610
Posted By FlatAddict
Re: Original Model A Parts $20 under

1. Speedometer Bezel, small crack $5.00
2. U-joint Clamps and a bearing retainer $10.00 Each
3. Water outlats/necks $5.00 each
4. Model A water pump bearing $3.00
5. Brake Shaft $5.00
6. Clutch...
Forum: Model-A 05-10-2011, 10:02 PM
Replies: 16
Views: 3,610
Posted By FlatAddict
Original Model A Parts $20 under

All items + shipping. PM for quotes.
Stuff added down below so scroll through.
1. Backing plate bolts long and short $5.00 for all (sold)
2. Backing Plates $5.00
3. Coil Clamp $2.00 Voltage...
Forum: Early V8 (1932-53) 03-15-2011, 08:59 PM
Replies: 2
Views: 1,649
Posted By FlatAddict
46' Ford Torque Tube Parts Question

What purpose does part # 4513 in the tube parts drawing serve? Why does it look like it's not installed in the other picture? I am trying to round up the right parts for my 46' trans install and it...
Forum: Early V8 (1932-53) 02-24-2011, 10:01 PM
Replies: 14
Views: 2,123
Posted By FlatAddict
Re: Distributor install

What is the hole on the distributor with the little flap that covers it? Just under where the cap sits.
Showing results 1 to 25 of 37

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:15 AM.