Forum: Model A (1928-31)
Today, 04:45 PM
|
|
Replies: 8
Views: 290
|
|
Forum: Model A (1928-31)
Today, 02:41 PM
|
|
Replies: 4
Views: 143
|
|
Forum: Model A (1928-31)
Today, 01:16 PM
|
|
Replies: 8
Views: 290
Re: New Shocks vs Rebuilt Shocks
And if you want to learn more, steve plucker developed this reference which covers many sources on the shock, and how to rebuild same.
https://www.fordbarn.com/forum/showthread.php?t=118682
|
|
Forum: Model A (1928-31)
Today, 12:54 PM
|
|
Replies: 8
Views: 290
Re: New Shocks vs Rebuilt Shocks
Look in the May-June Restorer (model A Ford Club) for sale ads.
I have sets forsale now.
https://www.fordbarn.com/forum/showthread.php?t=316736&highlight=Rebuilding+shocks
Should give you an...
|
|
Forum: Model A (1928-31)
Yesterday, 02:14 PM
|
|
Replies: 10
Views: 372
Re: Lifting 30 Tudor body
By elevating the body you can rollout the chassis. I don't trust trusses to handle much weight.
A 4wheel base that the detached body can set on, is an alternative.
|
|
Forum: Model A (1928-31)
Yesterday, 02:00 PM
|
|
Replies: 10
Views: 372
Re: Lifting 30 Tudor body
Try saw horses and 2x4s, you could go corner by corner, or back then front. 4 young bucks can lift the body as a unit. A floor Jack is your friend. Just watch your rafter clearances. Baby steps.
|
|
Forum: Model A (1928-31)
Yesterday, 12:53 PM
|
|
Replies: 32
Views: 1,678
Re: Cleaning the radiator
On your test drive the car will seek its coolant level, try just below the baffle. You are looking for keeping the engine from overheating. Especially under load, think hills.
I traded a Mitchell...
|
|
Forum: Model A (1928-31)
05-04-2024, 09:44 PM
|
|
Replies: 13
Views: 708
|
|
Forum: Model A (1928-31)
05-04-2024, 11:26 AM
|
|
Replies: 13
Views: 708
Re: Exhaust manifold intake bolts broke
It's a crap shoot, castings do vary, I tried direct tapping, but ended up with this fix.
If the initial retapping breaks thru the pocket in the casting you have a probable leak.
|
|
Forum: Model A (1928-31)
05-03-2024, 07:28 PM
|
|
Replies: 13
Views: 708
Re: Exhaust manifold intake bolts broke
I have drilled and tapped and installed a bolt, 3/8" or 1/2", cut flush, and then drilled and tapped for the manifold bolt. A plug if you will.
The casting has a pocket for the manifold bolt, and...
|
|
Forum: Model A (1928-31)
05-03-2024, 11:13 AM
|
|
Replies: 17
Views: 828
Re: Removing stuck distributor and lower shaft
Cut the shaft close to the bottom of the head, find a socket that is close to the diameter of the hole for the distributor and use that socket to tap out the distributor.
A soak in rust911 first if...
|
|
Forum: Model A (1928-31)
05-02-2024, 06:48 PM
|
|
Replies: 17
Views: 828
|
|
Forum: Model A (1928-31)
05-01-2024, 10:05 PM
|
|
Replies: 5
Views: 521
|
|
Forum: Model A (1928-31)
05-01-2024, 03:47 PM
|
|
Replies: 8
Views: 510
|
|
Forum: Model A (1928-31)
05-01-2024, 01:55 PM
|
|
Replies: 8
Views: 510
|
|
Forum: Model A (1928-31)
05-01-2024, 01:51 PM
|
|
Replies: 79
Views: 14,798
|
|
Forum: Model A (1928-31)
05-01-2024, 01:30 PM
|
|
Replies: 8
Views: 510
|
|
Forum: Model A (1928-31)
05-01-2024, 01:21 PM
|
|
Replies: 5
Views: 521
Shipping NOS axles
I thought this was a good way to ship axles to Austraulia.
Took months to get there. Arrived intact too!
https://m.youtube.com/watch?v=dA7nP94W51M
I have been trying to outsmart USPS when I...
|
|
Forum: Model A (1928-31)
04-29-2024, 01:18 PM
|
|
Replies: 2
Views: 246
Re: Oil line route
https://www.fordbarn.com/forum/showthread.php?t=66077
Might give you several ways to skin the cat.
|
|
Forum: Model A (1928-31)
04-29-2024, 01:07 PM
|
|
Replies: 21
Views: 984
Re: new guy, old car
Les Andrews red book, aka shop manual, is available thru the parts houses. It is a good reference.
|
|
Forum: Model A (1928-31)
04-29-2024, 11:53 AM
|
|
Replies: 21
Views: 984
|
|
Forum: Model A (1928-31)
04-29-2024, 11:30 AM
|
|
Replies: 21
Views: 1,083
|
|
Forum: Model A (1928-31)
04-28-2024, 08:51 PM
|
|
Replies: 21
Views: 1,083
|
|
Forum: Model A (1928-31)
04-28-2024, 01:27 PM
|
|
Replies: 13
Views: 1,171
|
|
Forum: Model A (1928-31)
04-27-2024, 12:36 PM
|
|
Replies: 5
Views: 714
|
