Forum: Early V8
04-20-2017, 07:31 AM
|
Replies: 0
Views: 612
Wanted 49 - 51
Need 49 - 51 fenders and hood, need front half, can have rot in wheel wells and hood can be bad in rear, also need grill opening, for a project, with a 86 Thunderbird.:cool:
|
Forum: Early V8 (1932-53)
07-02-2014, 07:59 AM
|
Replies: 60
Views: 13,329
|
Forum: Late V8 (1954+)
05-29-2014, 05:21 PM
|
Replies: 7
Views: 2,036
Re: Duel master
Thanks guys, figured it out, will try puting it on soon, had to change the rear wheel cylinders today, might change the the rubber hose and line to the master next, will need to check the fronts...
|
Forum: Late V8 (1954+)
05-29-2014, 06:53 AM
|
Replies: 7
Views: 2,036
Re: Duel master
Thanks JeffB2, I have done one on my 53 Merc, and 60 Chevy, they had swing pedals, having trouble with the truck with the pedal onto the floor.
|
Forum: Late V8 (1954+)
05-29-2014, 06:48 AM
|
Replies: 7
Views: 2,036
Re: Duel master
The old master wasn't there when I got the truck, how does the brake pedal, activate the master cylinder, think some of it is missing. Thanks
|
Forum: Late V8 (1954+)
05-28-2014, 03:40 PM
|
Replies: 7
Views: 2,036
Duel master
Any info will help, lost the instruction on the installation of a duel master cylinder for my 55 F100, have the kit, duel master, no booster, 2 diferent push rods, going to keep it all drum, reuse...
|
Forum: Late V8 (1954+)
05-22-2014, 05:02 PM
|
Replies: 15
Views: 3,453
|
Forum: Early V8 (1932-53)
05-20-2014, 07:34 AM
|
Replies: 3
Views: 1,169
Re: 52 Mercury engine startup
There is a small vaccum port for the distributor, it was on mine, it gives a very little vaccum to work the distributor, mine was clogged, very hard to know this, I finally put a rochester carb on...
|
Forum: Late V8 (1954+)
05-18-2014, 08:37 AM
|
Replies: 2
Views: 1,300
|
Forum: Early V8
05-14-2014, 08:20 AM
|
Replies: 0
Views: 895
Flywheel and clutch
Clutch and flywheel from a 49-51 F 100 (don't know which year but think they are the same) Was a hot rod!
|
Forum: Late V8
05-11-2014, 08:10 AM
|
Replies: 0
Views: 825
door
Complete driver side door for 53 Merc, will fit 52-54 and Fords
|
Forum: Early V8 (1932-53)
05-10-2014, 09:41 AM
|
Replies: 5
Views: 1,540
Re: 53 Mercury
I done my 53 a while back, take the gauge pod off, used the one wire at a time way for the gauges, changed it to 12 volt with a Fords under dash reducer ( NAPA has them, they were used on Ford trucks...
|
Forum: Early V8
05-08-2014, 07:24 AM
|
Replies: 0
Views: 1,031
Flathead parts
Flathead engine (50 or 51) I think, stuck cam or crank will not turn. Set of heads , 2 intake manifolds, flywheel and clutch, 53 Merc 2 barrel carb
|
Forum: Late V8
05-08-2014, 07:15 AM
|
Replies: 0
Views: 749
Door
1966-67 Mustang passenger door with glass
|
Forum: Late V8
05-08-2014, 07:03 AM
|
Replies: 0
Views: 858
O/D solenoid
Here is the # on it 10AR10B-62 in new condition.
|
Forum: Late V8
05-06-2014, 05:31 PM
|
Replies: 0
Views: 1,370
55 F100 project
55 F100, good cab, no engine/trans or bed, frame is good rebuilt stock front end, 9 in, extra pair of front fenders, cragars, new wiring harness.
|
Forum: Early V8 (1932-53)
05-01-2014, 05:19 PM
|
Replies: 31
Views: 9,174
|
Forum: Late V8 (1954+)
04-30-2014, 05:39 PM
|
Replies: 24
Views: 5,441
|
Forum: Late V8 (1954+)
04-28-2014, 05:13 PM
|
Replies: 13
Views: 2,613
|
Forum: Early V8 (1932-53)
04-21-2014, 05:36 AM
|
Replies: 12
Views: 2,029
Re: Overdrive selnoid
I used the 6 volt on my 53 Merc, which I changed to a 12 volt system, for years, worked just fine. Yes it has power at the terminal, but only goes in the selnoid when you put it in or out of...
|
Forum: Early V8 (1932-53)
03-23-2014, 08:25 AM
|
Replies: 30
Views: 7,471
Re: King pins
If you change the king pins, do it right, use the grease that is recomended, think, which ever ones you use, it will steer much better then then with the old ones!
|
Forum: Early V8 (1932-53)
03-22-2014, 08:13 AM
|
Replies: 17
Views: 2,764
Re: Need help with moons.
Had the same trouble with my 53 Merc, had to beat them on, never did find any that fit right. I used the 49 Ford hub cap, (not a moon but close) it was the best altenitive I could find that fit!! I...
|
Forum: Late V8 (1954+)
03-09-2014, 05:35 PM
|
Replies: 13
Views: 2,976
|
Forum: Late V8 (1954+)
02-26-2014, 06:15 PM
|
Replies: 2
Views: 1,256
|
Forum: Late V8 (1954+)
02-17-2014, 02:26 PM
|
Replies: 12
Views: 3,317
Re: Stuck Brake Drums
I just hit them, on the flat front, last time I used a large ball peen hammer, hit it with some good blows all around, might have to use that pry bar too, it should loosen right up. Might have to...
|