Forum: Early V8
02-21-2024, 10:23 PM
|
Replies: 1
Views: 461
|
Forum: Early V8 (1932-53)
02-07-2024, 11:56 AM
|
Replies: 131
Views: 643,061
|
Forum: Early V8 (1932-53)
02-07-2024, 03:51 AM
|
Replies: 131
Views: 643,061
|
Forum: Early V8
02-06-2024, 08:53 PM
|
Replies: 0
Views: 306
|
Forum: Early V8 (1932-53)
02-06-2024, 05:42 PM
|
Replies: 73
Views: 4,688
Re: T5 advice
This is what needs to be done to the tailhousing to convert it to mechanical speedo.
|
Forum: Early V8 (1932-53)
02-06-2024, 04:30 PM
|
Replies: 73
Views: 4,688
Re: T5 advice
Your mainshaft will work, You just need to remove the reluctor and put on a GM 7 tooth mech gear and clip. As far as the housing goes you need to mill down and weld in a fill piece, then machine a...
|
Forum: Early V8 (1932-53)
02-05-2024, 09:45 PM
|
Replies: 131
Views: 643,061
|
Forum: Early V8 (1932-53)
02-05-2024, 08:52 PM
|
Replies: 73
Views: 4,688
Re: T5 advice
Your friend is correct! the S10 4.03 1st gear is pretty much useless. The problem with the S10 transmissions is that the bulk of them were Non World Class T5's (1984-1992) And they are decent...
|
Forum: Early V8
02-01-2024, 10:43 PM
|
Replies: 0
Views: 214
|
Forum: Early V8
01-29-2024, 03:54 PM
|
Replies: 0
Views: 250
|
Forum: Early V8
01-29-2024, 12:22 AM
|
Replies: 1
Views: 461
|
Forum: Early V8 (1932-53)
01-26-2024, 02:16 AM
|
Replies: 34
Views: 2,477
Re: Mystery Blower
Agreed, Kinda of funny that a early hemi intake will bolt right on a Ardun engine. Zora is also the reason that we have a 327 chevy and the Famous DZ 302 chevy engine.
|
Forum: Model-A
01-25-2024, 07:54 PM
|
Replies: 1
Views: 494
|
Forum: Early V8 (1932-53)
01-25-2024, 03:10 PM
|
Replies: 73
Views: 4,688
Re: T5 advice
Tim, Depends on what you are putting it in as it doesn't work well in the earlier fords because it doesn't have the internal cross shaft and fork, Also like the merc bell you are limited to the...
|
Forum: Early V8 (1932-53)
01-25-2024, 12:44 PM
|
Replies: 73
Views: 4,688
Re: T5 advice
flathead47, Your right This is another good option as long as you are using a 49-52 motor. I have used this Bellhousing before with a 1/2 steel plate to adapt it to the T5. worked well
|
Forum: Early V8 (1932-53)
01-24-2024, 11:53 PM
|
Replies: 73
Views: 4,688
Re: T5 advice
Fair enough, And I agree with you he should keep selling his kit. I went though a Bad time in my life and because of some Bad choices I made years ago They still haunt me today. But I have made...
|
Forum: Early V8 (1932-53)
01-24-2024, 11:18 PM
|
Replies: 73
Views: 4,688
Re: T5 advice
Gary, I am unsure why you would be curious about me. Not like I am anybody special or anything. I tried to explain over and over that I in no way meant to offend you or hurt your feelings in...
|
Forum: Early V8 (1932-53)
01-24-2024, 09:01 PM
|
Replies: 73
Views: 4,688
Re: T5 advice
Here is a pic of Garys (cornhuskers kit) look at the throw out bearing. He presses a sleeve in the throwout bearing hub that fits on the T5 bearing retainer rather than pressing a sleeve on the...
|
Forum: Early V8 (1932-53)
01-24-2024, 08:08 PM
|
Replies: 73
Views: 4,688
Re: T5 advice
That should work just fine. What I mentioned about the sleeves is in the past guys have had trouble with them getting loose and turning on the bearing retainer. So with MDL's hogshead plate you had...
|
Forum: Early V8 (1932-53)
01-24-2024, 08:02 PM
|
Replies: 73
Views: 4,688
Re: T5 advice
You could have ordered the S10 T5 Bearing retainer as it will fit on any T5 and you could have used the Speedway sleeve. However as I posted above pressing a sleeve in the throwout bearing hub Like...
|
Forum: Early V8 (1932-53)
01-24-2024, 07:39 PM
|
Replies: 73
Views: 4,688
Re: T5 advice
Ziggster, What bellhousing are you using? Just wondering since you used the ford t5 bearing retainer Did you turn it down to fit a Speedway bellhousing?
|
Forum: Early V8 (1932-53)
01-24-2024, 06:56 PM
|
Replies: 73
Views: 4,688
Re: T5 advice
Man you need to get over yourself!! At 79 years old you should know better! I mean The nonsense in this last post makes you sound like a Cry baby toddler!! I myself and know one else here best I...
|
Forum: Early V8 (1932-53)
01-24-2024, 04:33 PM
|
Replies: 73
Views: 4,688
Re: T5 advice
Tim, that is what Speedway and Offy does. Your better off to do what Gary does and press a sleeve in the throwout bearing hub. If you do end up using a sleeve on the bearing retainer (from speedway)...
|
Forum: Early V8 (1932-53)
01-24-2024, 04:26 PM
|
Replies: 73
Views: 4,688
Re: T5 advice
Gary, You do not need a sleeve for the "Bond" adapter that I sell. As this is one of the best features that Dwight incorporated into his design. It uses the factory ford 32-48 ford bearing retainer...
|
Forum: Early V8 (1932-53)
01-24-2024, 02:02 PM
|
Replies: 73
Views: 4,688
Re: T5 advice
Gary, I meant no disrespect to you or what you sell, Also I forgot that the sleeve in your kit is in the throwout bearing and not pressed on the retainer. As a car builder I am always looking to...
|