Forum: Early V8 (1932-53)
04-07-2024, 11:30 PM
|
Replies: 11
Views: 940
|
Forum: Early V8 (1932-53)
04-07-2024, 08:43 PM
|
Replies: 11
Views: 940
Navarro aftermarket heads
I know a lot of discussion has taken place about spark plugs and Aluminum after market heads but I have not been able to find an answer to my specific problem. I have Navarro heads from H&H Flatheads...
|
Forum: Early V8 (1932-53)
11-06-2023, 11:18 AM
|
Replies: 13
Views: 657
|
Forum: Early V8 (1932-53)
11-06-2023, 10:34 AM
|
Replies: 13
Views: 657
|
Forum: Early V8 (1932-53)
11-06-2023, 10:32 AM
|
Replies: 13
Views: 657
|
Forum: Early V8 (1932-53)
11-06-2023, 12:45 AM
|
Replies: 13
Views: 657
|
Forum: Early V8 (1932-53)
11-05-2023, 10:54 PM
|
Replies: 13
Views: 657
|
Forum: Early V8 (1932-53)
11-05-2023, 09:16 PM
|
Replies: 13
Views: 657
Need Limeworks steering wheel help
I'm installing a banjo steering wheel from Limeworks and have run into a horn button wiring issue. The steering wheel is second hand and I have no installation instructions. I've attached a picture...
|
Forum: Early V8 (1932-53)
10-12-2023, 05:39 PM
|
Replies: 17
Views: 1,341
Re: Brake troubles
Thanks for the input guys. I talked to Speedway and they said they hadn't encountered my problem before. They advised shaving the outside edge a little to gain some relief.
|
Forum: Early V8 (1932-53)
10-12-2023, 03:05 PM
|
Replies: 17
Views: 1,341
Re: Brake troubles
Newc, thanks for the response, the spindles (https://www.speedwaymotors.com/Speedway-1928-1948-Ford-Milled-Forged-Spindles-w-King-Pins,352717.html)
and bearing kit...
|
Forum: Early V8 (1932-53)
10-12-2023, 02:36 PM
|
Replies: 17
Views: 1,341
Brake troubles
Installed the speedway Bendix Style Brakes for 1937-48 Ford Spindles recently and am having grinding problems. This is a new build and all front end components are brand new. Whenever I apply...
|
Forum: Early V8
02-24-2023, 03:08 PM
|
Replies: 0
Views: 357
1932-48 Ford 18 tooth speedometer drive
FOUND ONE, THANKS FOR LOOKING.
Need to replace my current 19 tooth speedometer drive and housing with a 17 tooth gear and 18 tooth housing. I've located the 17 tooth gear (Bratton's) but need a 18...
|
Forum: Early V8
02-01-2023, 12:09 PM
|
Replies: 0
Views: 415
32 pitman arm
Found one from Yankee Mike here on the Barn. Thanks
Looking for 1932 Ford pitman arm for car. Prefer one with good splines and reasonable price. TIA
Tony
|
Forum: Early V8 (1932-53)
10-06-2022, 07:21 PM
|
Replies: 9
Views: 1,499
Re: Axle Nut source
I got a hold of barnfind 08 and have two NOS Ford axle nuts on the way. Thanks for the help and information.
Tony
|
Forum: Early V8 (1932-53)
10-06-2022, 08:49 AM
|
Replies: 9
Views: 1,499
|
Forum: Early V8 (1932-53)
10-05-2022, 09:31 PM
|
Replies: 9
Views: 1,499
Re: Axle Nut source
Thanks Ozyrodder, I'll give them a call in the morning and see what they say.
Tony
|
Forum: Early V8 (1932-53)
10-05-2022, 07:17 PM
|
Replies: 9
Views: 1,499
Axle Nut source
Looking for a source of hardened axle nuts for a 1940 rear axle. I was installing the rear driver's side hub when I went to torque the axle nut to 200 ft/lbs. the nut stripped. I only got to 175...
|
Forum: Model-A
09-07-2022, 02:45 PM
|
Replies: 0
Views: 429
1930/31 Cowl Band
Hi, like everyone else I am looking for a stainless 1930/31 Cowl Band for a Coupe. TIA.
|
Forum: Early V8 (1932-53)
08-10-2022, 08:28 AM
|
Replies: 22
Views: 1,957
|
Forum: Early V8 (1932-53)
08-09-2022, 01:28 PM
|
Replies: 22
Views: 1,957
Re: Help with 36 Column Drop Ignition
rich b, I’m going to you use the radio power wire on pin 30 since I won’t be running a radio. I’ll be sure to fuse it. Earlier you mentioned a ballast resistor on the coil circuit; if I’m running a...
|
Forum: Early V8 (1932-53)
08-08-2022, 06:55 PM
|
Replies: 22
Views: 1,957
|
Forum: Early V8 (1932-53)
08-08-2022, 01:31 PM
|
Replies: 22
Views: 1,957
Re: Help with 36 Column Drop Ignition
Thank you gentlemen.
rich b I will use the Orange Ign ACC wire on the start button relay pin 30 if that's OK.
Tim, thank you for your generous offer but I've ordered the two relays shown in...
|
Forum: Early V8 (1932-53)
08-08-2022, 09:24 AM
|
Replies: 22
Views: 1,957
Re: Help with 36 Column Drop Ignition
Would these work?
https://m.media-amazon.com/images/I/61xmReZuigL._AC_UY218_.jpg
EHDIS Car Relay 4 Pin 12v 40amp Spst Model No.: JD2912-1H-12VDC 40A 14VDC, Auto Switches & Starters,Pack of 2
|
Forum: Early V8 (1932-53)
08-08-2022, 09:16 AM
|
Replies: 22
Views: 1,957
Re: Help with 36 Column Drop Ignition
Thanks very much for the help rich b. A couple of questions if you don't mind. It looks like only two wires go to the actual switch terminals; one from the relay pin 86 and the other from a good...
|
Forum: Early V8 (1932-53)
08-07-2022, 08:19 PM
|
Replies: 22
Views: 1,957
|