Forum: Early V8 (1932-53)
10-18-2019, 10:53 AM
|
Replies: 15
Views: 2,642
|
Forum: Model-A
09-08-2019, 04:58 PM
|
Replies: 0
Views: 971
|
Forum: Model A (1928-31)
07-08-2019, 03:52 PM
|
Replies: 7
Views: 2,108
Re: Roadster door rubber help
i just did this on my 28. below is a thread on the HAMB with photos of how things go together.
https://www.jalopyjournal.com/forum/threads/roadster-door-dilemma.1143035/#post-13018232
|
Forum: Early V8 (1932-53)
06-26-2019, 09:45 PM
|
Replies: 11
Views: 2,736
|
Forum: Early V8 (1932-53)
06-26-2019, 08:52 PM
|
Replies: 11
Views: 2,736
More banjo questions for the gurus
I’m on the home stretch of my banjo rebuild and everything is going together very well and smooth.
My backlash is set and I have my gasket combination figured out. When I pull things back apart...
|
Forum: Early V8 (1932-53)
06-24-2019, 01:17 PM
|
Replies: 5
Views: 1,811
|
Forum: Early V8 (1932-53)
06-17-2019, 08:32 PM
|
Replies: 17
Views: 4,233
Re: Help with banjo rear
I pulled the bearings from the carrier and the races from the bells. It turns out that the carrier bearings are early banjo 18-4221 original ford stamped. The races are new bearing size. The part...
|
Forum: Early V8 (1932-53)
06-14-2019, 11:26 AM
|
Replies: 17
Views: 4,233
Re: Help with banjo rear
I have photos but I can’t seem to get them loaded from my mobile device. My guess is that it was slapped together but not ran.... like I said I drove it once (didn’t notice the side to side play...
|
Forum: Early V8 (1932-53)
06-14-2019, 10:55 AM
|
Replies: 17
Views: 4,233
|
Forum: Early V8 (1932-53)
06-14-2019, 10:01 AM
|
Replies: 17
Views: 4,233
Re: Help with banjo rear
I’ve been studying the rebuild guide and some website references and have a pretty general idea. I get the shimming on the bells to change the preload. The issue with mine is less of the minute...
|
Forum: Early V8 (1932-53)
06-11-2019, 07:04 AM
|
Replies: 17
Views: 4,233
Re: Help with banjo rear
I’m guessing that someone installed incorrect bearings on the carrier... does anyone have dimensions of the correct bearing sizes? I can try to measure what I have before I but new
|
Forum: Early V8 (1932-53)
06-10-2019, 06:50 PM
|
Replies: 17
Views: 4,233
Help with banjo rear
I pulled the banjo out of my roadster. I drove it once and noticed some pretty loud howel on deceleration.
What I know
I think it’s a 40’
-The gearing has matched etching from ford that says 3.57...
|
Forum: Early V8
06-03-2019, 10:42 PM
|
Replies: 0
Views: 1,028
|
Forum: Early V8 (1932-53)
05-12-2019, 08:18 AM
|
Replies: 10
Views: 2,713
Re: Help with a noisy Banjo rear end.
Thank you for the in depth explanation on setup! I did talk to Tim at Berts llast month when I was in. I explained what I was hearing and asked if they could work on it. They mentioned that the later...
|
Forum: Early V8 (1932-53)
05-10-2019, 01:42 PM
|
Replies: 10
Views: 2,713
|
Forum: Early V8 (1932-53)
05-09-2019, 03:19 PM
|
Replies: 10
Views: 2,713
Help with a noisy Banjo rear end.
I have a 37 or 38 banjo rear in my 28 roadster with a closed drive / 39 trans. Everything is hearsay because i bought this car unfinished. The P.O simply stated that he installed a matched set 3.54...
|
Forum: Early V8
04-29-2019, 09:10 PM
|
Replies: 0
Views: 1,271
|
Forum: Early V8 (1932-53)
04-03-2019, 04:36 PM
|
Replies: 43
Views: 6,782
Re: 1935 V8 convirteble sedan engine broken
i would start by checking the oil level. Then change the oil to the proper weight. Run an engine compression check.
in that order.
i've had a couple flatheads smoke for a few miles until the...
|
Forum: Model A (1928-31)
03-25-2019, 03:48 PM
|
Replies: 2
Views: 909
|
Forum: Model A (1928-31)
03-24-2019, 01:46 PM
|
Replies: 2
Views: 909
|
Forum: Late V8
02-22-2019, 07:57 PM
|
Replies: 0
Views: 1,147
1948-1952 f-1-2-3 steering box
I’m looking for a steer box for my 50 f1. From what I’ve read they are the same f-1-2-3?
Let me know if you have something, I’d like to line something up by spring.
Byron
3oh3-601-59sevenseven.
|
Forum: Early V8 (1932-53)
12-03-2015, 09:52 PM
|
Replies: 45
Views: 7,514
Re: A 1949 F1 preservation
I would pull the intake and address things from the lifter valley. It would also be good insurance to have a new intake gasket. You never know what may have crawled down the carb to build a nest...
|
Forum: Early V8 (1932-53)
11-19-2015, 12:22 PM
|
Replies: 5
Views: 1,209
|
Forum: Early V8 (1932-53)
11-19-2015, 10:45 AM
|
Replies: 5
Views: 1,209
8ba leaky heater shutoff valve
at this point i am not running a heater so i currently have the valve closed and a section of heater hose connected to the passenger water pump to cap the pump output.the valve leaks at the shaft...
|
Forum: Early V8 (1932-53)
11-16-2015, 10:50 PM
|
Replies: 5
Views: 1,275
|