Forum: Model-A
10-10-2013, 09:24 PM
|
Replies: 5
Views: 3,530
|
Forum: Model-A
10-06-2013, 04:54 PM
|
Replies: 5
Views: 3,530
|
Forum: Model-A
10-02-2013, 10:01 PM
|
Replies: 5
Views: 3,530
|
Forum: Model-A
09-30-2013, 05:47 AM
|
Replies: 5
Views: 3,530
|
Forum: Model-A
09-30-2013, 05:44 AM
|
Replies: 5
Views: 3,530
1930 Ford Model A 5 Window Coupe
For sale is a 1930 Ford Model Five Window Coupe. The body is rough but salvageable. It is a rumble lid coupe. The chassis and engine were restored at some point in the past. The body is one I had and...
|
Forum: Early V8
03-24-2012, 07:30 AM
|
Replies: 6
Views: 2,796
|
Forum: Early V8
03-09-2012, 09:21 PM
|
Replies: 6
Views: 2,796
|
Forum: Early V8
02-27-2012, 10:17 PM
|
Replies: 6
Views: 2,796
|
Forum: Early V8
02-22-2012, 11:50 PM
|
Replies: 6
Views: 2,796
|
Forum: Early V8
02-17-2012, 07:25 AM
|
Replies: 6
Views: 2,796
|
Forum: Early V8 (1932-53)
02-11-2012, 08:55 PM
|
Replies: 4
Views: 1,460
Flathead Questions?
1. Will a dual carb 255 Merc Flathead run on 6 volt? or at least fire or sputter?
2. Will a dual carbed 255 Merc Flathead running 6 volt produce a low compression number?:)
|
Forum: Early V8
02-10-2012, 10:26 PM
|
Replies: 6
Views: 2,796
|
Forum: Early V8
02-10-2012, 10:24 PM
|
Replies: 6
Views: 2,796
1939 Ford Coupe
1939 Ford Coupe. 350/350 combo, about 400hp. Listing this for a friend so give him a call for more info. His name is Jerry. Cell: 406.263.4409 or at home: 406.228.9044
|
Forum: Model-A
01-21-2012, 10:16 PM
|
Replies: 0
Views: 965
28'-29' 1/4 Window Garnish Moulding A Coupe
Interior Quarter Window Garnish Moulding for a 28'-29' Ford Model A Coupe. I think it is passenger side. Surface rust, some pitting but no holes or rust through. $60.00 shipped in lower 48 will trade...
|
Forum: Model-A
06-03-2011, 06:16 AM
|
Replies: 16
Views: 3,662
|
Forum: Model-A
05-30-2011, 09:41 PM
|
Replies: 16
Views: 3,662
|
Forum: Model-A
05-27-2011, 08:32 PM
|
Replies: 16
Views: 3,662
|
Forum: Model-A
05-23-2011, 10:22 PM
|
Replies: 16
Views: 3,662
|
Forum: Model-A
05-18-2011, 09:10 PM
|
Replies: 16
Views: 3,662
|
Forum: Model-A
05-15-2011, 09:02 AM
|
Replies: 16
Views: 3,662
|
Forum: Model-A
05-11-2011, 10:07 PM
|
Replies: 16
Views: 3,662
Re: Original Model A Parts $20 under
Don't mean to early bump just need to add stuff.
1. Oil Filler Tube $3.00
2. Shift Tower for a 30' AA 4spd $20.00
3. Brake Shoe Cores $10.00 for all. (SOLD)
4. Sport Coupe Top Iron $20.00
5....
|
Forum: Model-A
05-10-2011, 10:08 PM
|
Replies: 16
Views: 3,662
Re: Original Model A Parts $20 under
1. Speedometer Bezel, small crack $5.00
2. U-joint Clamps and a bearing retainer $10.00 Each
3. Water outlats/necks $5.00 each
4. Model A water pump bearing $3.00
5. Brake Shaft $5.00
6. Clutch...
|
Forum: Model-A
05-10-2011, 10:02 PM
|
Replies: 16
Views: 3,662
Original Model A Parts $20 under
All items + shipping. PM for quotes.
Stuff added down below so scroll through.
1. Backing plate bolts long and short $5.00 for all (sold)
2. Backing Plates $5.00
3. Coil Clamp $2.00 Voltage...
|
Forum: Early V8 (1932-53)
03-15-2011, 08:59 PM
|
Replies: 2
Views: 1,711
46' Ford Torque Tube Parts Question
What purpose does part # 4513 in the tube parts drawing serve? Why does it look like it's not installed in the other picture? I am trying to round up the right parts for my 46' trans install and it...
|
Forum: Early V8 (1932-53)
02-24-2011, 10:01 PM
|
Replies: 14
Views: 2,138
Re: Distributor install
What is the hole on the distributor with the little flap that covers it? Just under where the cap sits.
|