Go Back   The Ford Barn > Search Forums
Reload this Page Search Results

Sponsored Links (Register now to hide all advertisements)

Page 1 of 20 1 234511 Last »
Showing results 1 to 25 of 500
Search took 0.11 seconds. Search: Posts Made By: Bob C
Forum: Model A (1928-31) Today, 01:42 PM
Replies: 27
Views: 2,709
Posted By Bob C
Re: Distributor won't drop in fully...

The short answer is probably not as it's hard to get to the lower shaft because of the spring that hold the oil pump drive gear in place. I had one that was really stuck and I had to make a collet...
Forum: Model A (1928-31) Yesterday, 08:10 PM
Replies: 2
Views: 161
Posted By Bob C
Re: Sidemount irons - 1930 Coupe

The supports are the same, the wheel carrier flange are left and right.
Forum: Early V8 (1932-53) Yesterday, 05:25 PM
Replies: 39
Views: 1,292
Posted By Bob C
Re: Front Axle 1939 Ford pickup

The lock pin for the king pin is the same 1928-48 and I have the blue prints for the Model A axle and the hole is reamed .561-.563,
it's not tapered.
Forum: Early V8 (1932-53) Yesterday, 11:16 AM
Replies: 39
Views: 1,292
Posted By Bob C
Re: Front Axle 1939 Ford pickup

With that spring being down from the cross member so far
is going to affect the caster.
Forum: Early V8 (1932-53) 06-05-2024, 10:03 AM
Replies: 14
Views: 311
Posted By Bob C
Re: 1950 Mercury add factory OD

I think the driveshaft is the same but you will need the whole transmission.
Forum: Early V8 (1932-53) 06-04-2024, 03:31 PM
Replies: 8
Views: 348
Posted By Bob C
Re: 1940 master cylinder repair kit

How about a picture of it or the size.
Forum: Model A (1928-31) 06-04-2024, 12:41 PM
Replies: 1
Views: 133
Posted By Bob C
Re: Connecting the light switch

The notch in the contact plate and the lower part of the switch
go in a tab in the upper part of the switch. You can see the tab in the picture right above the bolt.
Forum: Model A (1928-31) 06-04-2024, 12:11 PM
Replies: 9
Views: 464
Posted By Bob C
Re: Do the Motor Mounts get wired around the bolts

Page 1-5 of the Judging Standards, second paragraph
third line.
Forum: Model A (1928-31) 06-01-2024, 09:04 PM
Replies: 3
Views: 375
Posted By Bob C
Re: just a quickie

I just measured one, like said above 11/16"
Forum: Model A (1928-31) 06-01-2024, 02:16 PM
Replies: 24
Views: 1,026
Posted By Bob C
Re: Different length rear axle shaft threads on either side?

Also make sure the axle and hub tapers are spotless, no grease,oil
or never seize.
Forum: Model A (1928-31) 05-31-2024, 09:38 PM
Replies: 24
Views: 1,026
Posted By Bob C
Re: Different length rear axle shaft threads on either side?

May be the pictures but I don't see any washers under the nuts.
Forum: Model A (1928-31) 05-29-2024, 10:06 AM
Replies: 27
Views: 1,610
Posted By Bob C
Re: Move A By Yourself

Here you go, ain't cheap. https://duckduckgo.com/?t=h_&q=light+airplane+tug&iax=shopping&ia=shopping
Forum: Early V8 (1932-53) 05-27-2024, 02:42 PM
Replies: 39
Views: 1,292
Posted By Bob C
Re: Front Axle 1939 Ford pickup

Not familiar with V8 axles and it may be the picture but this one does
not appear to be straight.
Forum: Model A (1928-31) 05-25-2024, 02:29 PM
Replies: 6
Views: 401
Posted By Bob C
Re: Throw out bearing grease fitting

The ones I have are 1/8 pipe thread and that's what the parts book shows.
Forum: Early V8 (1932-53) 05-25-2024, 10:09 AM
Replies: 8
Views: 556
Posted By Bob C
Re: Brake stud repair tool

Here is a link to Vince's site showing how to swage the stud.
https://www.fordgarage.com/pages/swaging.htm
Forum: Model A (1928-31) 05-24-2024, 09:04 PM
Replies: 14
Views: 470
Posted By Bob C
Re: installing grease baffle on front wheels Model AA truck

Here are some pictures of the AA spindle, grease baffle and hub.
The spindle has a front hub dust cap mounted on the spindle just like the Model A. the hub sticks inside the grease baffle so the...
Forum: Model A (1928-31) 05-24-2024, 11:00 AM
Replies: 6
Views: 498
Posted By Bob C
Re: Ford Tool Identification

Here you go. https://www.snydersantiqueauto.com/product.htm?pid=979976&cat=41621
Forum: Early V8 (1932-53) 05-23-2024, 08:15 PM
Replies: 12
Views: 367
Posted By Bob C
Re: Stake bed gate hinges

Could you modify these to make what you need?
https://www.buyersproducts.com/product/straight-stake-rack-connector-set-753
Forum: Model A (1928-31) 05-23-2024, 06:41 PM
Replies: 11
Views: 766
Posted By Bob C
Re: Nothing Seems to Fit!

Do you have another sector shaft that you can try the pitman arm
on to see which part is the problem?
Forum: Early V8 (1932-53) 05-23-2024, 04:44 PM
Replies: 12
Views: 367
Posted By Bob C
Re: Stake bed gate hinges

Might check on the AA site. http://forums.aa-fords.com/
Forum: Model A (1928-31) 05-23-2024, 10:28 AM
Replies: 14
Views: 470
Posted By Bob C
Re: installing grease baffle on front wheels Model AA truck

Here's a AA brake.
Forum: Model A (1928-31) 05-22-2024, 07:41 PM
Replies: 16
Views: 1,065
Posted By Bob C
Re: 1931 model a engine

Another way to check the flatness of the block and head is like

Terry Burtz show in the builders guide.
"Place short pieces of oiled Plastigage around various locations on the cylinder block,...
Forum: Model A (1928-31) 05-22-2024, 01:42 PM
Replies: 18
Views: 804
Posted By Bob C
Re: valve guide question

This is the kit that the guides have an interference fit.
Forum: Early V8 (1932-53) 05-21-2024, 07:43 PM
Replies: 4
Views: 271
Posted By Bob C
Re: Holley 94 part id. Distrib vacuum dealie?

Does it look like this?
OK I see it in your album. It's for a Southwind gasoline heater.
Forum: Early V8 (1932-53) 05-21-2024, 02:24 PM
Replies: 11
Views: 620
Posted By Bob C
Re: Banjo rear end hub, axle bearings and seals

The SL-3131 bearing grease is no longer available.
Showing results 1 to 25 of 500
Page 1 of 20 1 234511 Last »

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:47 PM.