Forum: Early V8 (1932-53)
05-13-2024, 07:58 PM
|
Replies: 9
Views: 361
|
Forum: Early V8 (1932-53)
05-12-2024, 09:22 PM
|
Replies: 9
Views: 361
|
Forum: Model-T
05-12-2024, 08:13 PM
|
Replies: 1
Views: 1,028
|
Forum: Early V8 (1932-53)
05-12-2024, 08:11 PM
|
Replies: 9
Views: 361
What water pumps do I need?
I'm putting an 8CM Merc in my '46 1/2 ton pickup. I need water pumps that will work with the wide belt and that will line up with the '46 engine mounts. The 59A pumps appear to be quite a bit...
|
Forum: Early V8 (1932-53)
05-04-2024, 08:49 PM
|
Replies: 3
Views: 309
Ford pattern S10 T5 to 8BA?
I have a later S10 T5 with the Ford bolt pattern. What adapter do I need to bolt this to an 8BA? This will be going in a '46 pickup and I'll need the original clutch linkage to work. Thanks in...
|
Forum: Early V8 (1932-53)
03-07-2024, 09:09 AM
|
Replies: 5
Views: 521
|
Forum: Early V8 (1932-53)
03-05-2024, 09:55 PM
|
Replies: 5
Views: 521
46 pickup flathead headers?
What headers will fit a flathead in a '46 pickup? I only see them listed for '48-'52. Will they work or are they not even close? Any other recommendations?
|
Forum: Late V8 (1954+)
02-08-2024, 04:58 PM
|
Replies: 4
Views: 657
Master Cylinder which port is which
I'm putting a '69 Mustang drum/drum master cylinder in my '46 pickup. Does it matter which port goes to the front or rear since both reservoirs are the same size?
|
Forum: Early V8 (1932-53)
02-08-2024, 01:30 PM
|
Replies: 20
Views: 1,604
Re: NP435 to flathead?
My bad, it's a '46 so open driveline which makes it tons easier. The truck has a 59A in it right now, but I'm building an 8CM for it. I wasn't planning to swap the engine until next winter so if I...
|
Forum: Early V8 (1932-53)
02-08-2024, 10:14 AM
|
Replies: 20
Views: 1,604
NP435 to flathead?
I've got an NP435 transmission with a Borg Warner R10 overdrive on it that I'd like to swap into my truck. Is there an easy way to get this bolted up to the flathead?
|
Forum: Early V8
01-24-2024, 09:42 PM
|
Replies: 0
Views: 271
|
Forum: Model-T
01-17-2024, 07:53 PM
|
Replies: 1
Views: 1,028
FS - 26 T Roadster Hot Rod
1926 Model T Roadster. Professionally built Chevy 350, 700R4 with shift kit and converter. Triangulated 4 link rear with QA1 coilovers, 9 inch, 3.50's. Quarterelliptic front. '40 front axle with...
|
Forum: Early V8 (1932-53)
01-17-2024, 07:17 PM
|
Replies: 2
Views: 425
Leaf spring pin removal
'46 1/2 ton pickup. How does the forward leaf spring pin remove from the rear springs? Is that a wedge pin that I've circled? Remove the wedge pin then the main pin should pull out? Waiting for my...
|
Forum: Early V8 (1932-53)
01-13-2024, 09:30 PM
|
Replies: 10
Views: 660
|
Forum: Early V8 (1932-53)
01-12-2024, 09:45 PM
|
Replies: 4
Views: 405
|
Forum: Early V8 (1932-53)
01-12-2024, 09:45 PM
|
Replies: 10
Views: 660
Which intake to clear generator?
I'm hotrodding a '49 Merc for my '46 pickup. I'd like to run a dual carb intake, but which one will clear the generator? I can't offset mount the gen because the fan attaches to it. Thanks in...
|
Forum: Early V8 (1932-53)
01-11-2024, 05:50 PM
|
Replies: 4
Views: 405
Rear axle ID help
What rear axle is this in my '46 pickup? To my knowledge it should be a banjo with open driveline. The pinion angle is also all kinds of wrong..
|
Forum: Early V8 (1932-53)
12-09-2023, 06:21 PM
|
Replies: 7
Views: 828
|
Forum: Early V8 (1932-53)
12-07-2023, 09:46 AM
|
Replies: 7
Views: 828
'46 pickup engine/trans swap advice needed
I just brought home a '46 Ford pickup with a decent running flathead in it. The seller told me the engine is a '40 but I don't know how to verify that. He also had a Merc engine sitting on the floor...
|
Forum: Late V8 (1954+)
09-24-2022, 03:24 PM
|
Replies: 8
Views: 1,447
Re: What brakes are these?
Great info. I wasn't aware that was all available on Raybestos' website. As near as I can tell, the axle is a '58 with these brakes stuck on it. The drums clearly don't match the rest so I wouldn't...
|
Forum: Late V8 (1954+)
09-24-2022, 03:14 PM
|
Replies: 8
Views: 1,447
|
Forum: Early V8 (1932-53)
09-24-2022, 01:26 AM
|
Replies: 6
Views: 885
|
Forum: Late V8 (1954+)
09-23-2022, 10:06 PM
|
Replies: 8
Views: 1,447
Re: What brakes are these?
It's 5x4-1/2. I haven't found any stamping in the plates. The drum has 37582 D60A 1126 BA. They measure 11x2-1/4" as do the shoes. It's anyone's guess what the axle originally came out of and I doubt...
|
Forum: Late V8 (1954+)
09-23-2022, 07:59 PM
|
Replies: 8
Views: 1,447
What brakes are these?
Hoping someone can help ID these brakes. They're on a '58 9 inch. I'm assuming the drums are incorrect. There is a 1/4" spacer between the hub face and drum. Without the spacer the drum rubs on the...
|
Forum: Early V8 (1932-53)
09-23-2022, 06:14 PM
|
Replies: 6
Views: 885
|