Forum: Early V8 (1932-53)
05-21-2024, 10:02 PM
|
|
Replies: 12
Views: 510
|
|
Forum: Early V8 (1932-53)
05-17-2024, 09:09 AM
|
|
Replies: 106
Views: 7,561
|
|
Forum: Early V8 (1932-53)
05-13-2024, 06:14 PM
|
|
Replies: 12
Views: 925
|
|
Forum: Early V8 (1932-53)
05-12-2024, 10:15 AM
|
|
Replies: 12
Views: 925
|
|
Forum: Early V8 (1932-53)
05-12-2024, 10:00 AM
|
|
Replies: 12
Views: 510
|
|
Forum: Early V8 (1932-53)
05-12-2024, 09:59 AM
|
|
Replies: 12
Views: 510
|
|
Forum: Early V8 (1932-53)
05-12-2024, 09:59 AM
|
|
Replies: 12
Views: 510
|
|
Forum: Early V8 (1932-53)
05-11-2024, 06:03 PM
|
|
Replies: 12
Views: 510
|
|
Forum: Early V8 (1932-53)
05-11-2024, 01:51 PM
|
|
Replies: 12
Views: 925
|
|
Forum: Early V8 (1932-53)
05-11-2024, 01:48 PM
|
|
Replies: 12
Views: 510
1947 1.5-Ton Front Leaf Spring
Hello,
I recently bought a 47 1.5 ton grain truck which is in need of a new front spring. Does anyone have any ideas where I might find one of those? Everything I see is for the 1/2 tons or...
|
|
Forum: Early V8 (1932-53)
05-07-2024, 09:13 PM
|
|
Replies: 12
Views: 925
|
|
Forum: Early V8 (1932-53)
05-06-2024, 05:33 PM
|
|
Replies: 12
Views: 925
|
|
Forum: Early V8 (1932-53)
05-05-2024, 03:31 PM
|
|
Replies: 12
Views: 925
Flathead Machine Shop-Utah
Good afternoon,
Does anyone know of a reputable machine shop in Utah that will do work on flatheads?
Thanks.
Dale
|
|
Forum: Early V8 (1932-53)
03-21-2024, 12:36 PM
|
|
Replies: 6
Views: 486
|
|
Forum: Early V8 (1932-53)
03-21-2024, 12:36 PM
|
|
Replies: 6
Views: 486
|
|
Forum: Early V8 (1932-53)
03-20-2024, 07:39 PM
|
|
Replies: 6
Views: 486
|
|
Forum: Early V8 (1932-53)
03-19-2024, 08:16 PM
|
|
Replies: 6
Views: 486
47 PU Fuel Tank Shutoff Valve Fitting
Good evening,
Does anyone know where I can find this fitting that mates up to the fuel tank fuel shutoff valve? I've got a couple trucks without this. It appears they were cut off to use...
|
|
Forum: Early V8 (1932-53)
10-02-2022, 02:31 PM
|
|
Replies: 5
Views: 634
Re: 47 6-Cylinder Choke and Throttle Cable Ends
Ken...what you described is the way I will have to go. Thanks for the info. With only the 6 cylinders using the "cable" I'm not surprised the ends aren't available. Adapt and overcome as they say!
|
|
Forum: Early V8 (1932-53)
10-02-2022, 11:28 AM
|
|
Replies: 5
Views: 634
47 6-Cylinder Choke and Throttle Cable Ends
Good morning,
Does anyone know where I could find the spring-loaded ends for choke and throttle cables for G-series 6-cylinder? I need to replace these cables and would like to use new ends as...
|
|
Forum: Early V8 (1932-53)
09-01-2022, 01:03 PM
|
|
Replies: 18
Views: 2,264
|
|
Forum: Early V8 (1932-53)
08-31-2022, 08:57 PM
|
|
Replies: 18
Views: 2,264
Re: 47 Pickup Banjo Rear-End Blues
Mart...well, I was able to get the nut off using the business end of a large crescent wrench as a hammer to turn the nut. Pulled the brake drum off and there she was, the key, well about half of her...
|
|
Forum: Early V8 (1932-53)
08-31-2022, 01:06 PM
|
|
Replies: 18
Views: 2,264
Re: 47 Pickup Banjo Rear-End Blues
Thanks to all for your insights and suggestions! I was watching The Andy Griffith Show re-runs last night and I ran across the episode where Barney buys a car from a sweet lady who only drove it to...
|
|
Forum: Early V8 (1932-53)
08-30-2022, 09:06 PM
|
|
Replies: 18
Views: 2,264
47 Pickup Banjo Rear-End Blues
Good evening,
Where to start? I've got a 4 speed 6-cylinder 47 pickup with the banjo rear-end. Over the past 10 months I have managed to get the engine running and cleaned up the tranny. One...
|
|
Forum: Early V8 (1932-53)
08-12-2022, 09:56 AM
|
|
Replies: 2
Views: 521
4 Speed Countergear Thrust Washers
Good morning,
I'm in need of a few 59T-7129 thrust washers for my 4 speeds.
Unfortunately, Van Pelts was zero balance on these washers when I ordered my other parts yesterday. Does anyone...
|
|
Forum: Early V8 (1932-53)
07-02-2022, 07:26 PM
|
|
Replies: 4
Views: 633
|
