Forum: Model A (1928-31)
Yesterday, 11:15 PM
|
Replies: 28
Views: 4,899
Re: Tools/supplies needed while traveling
Carbs will experience more wear under the seat of a car than on the engine. I can drop and clean the carb quicker than you can removing, finding the spare and bolting the replacement on.
The...
|
Forum: Model A (1928-31)
Yesterday, 11:09 PM
|
Replies: 5
Views: 157
Re: Door alignment problem on 29 CCPU
I agree that hinge adjustments will likely get you closer to the solution, we cannot say for sure until it’s on the frame and adjusted. Shimming and bolting onto the frame account for a decent...
|
Forum: Model A (1928-31)
06-08-2024, 10:54 PM
|
Replies: 5
Views: 157
|
Forum: Model-A
06-07-2024, 03:43 PM
|
Replies: 4
Views: 723
|
Forum: Early V8
06-07-2024, 03:42 PM
|
Replies: 2
Views: 177
|
Forum: Model-A
06-07-2024, 03:42 PM
|
Replies: 7
Views: 1,091
|
Forum: Model-A
06-07-2024, 03:41 PM
|
Replies: 3
Views: 606
|
Forum: Model A (1928-31)
05-26-2024, 11:22 PM
|
Replies: 28
Views: 1,755
|
Forum: Model A (1928-31)
05-26-2024, 06:02 PM
|
Replies: 21
Views: 1,099
Re: Another carb needs repair
As is typically the case, we respond with missing info. I don’t use Tillotson carbs, so my comments apply to the factory issued Zenith carbs.
|
Forum: Model A (1928-31)
05-24-2024, 11:10 PM
|
Replies: 21
Views: 1,099
Re: Another carb needs repair
Those threads are for compression fittings. I’m not sure heli coils are made for a compression fitting to properly work. I don’t think time serts are made for that application either.
I’d look...
|
Forum: Model A (1928-31)
05-24-2024, 06:23 PM
|
Replies: 7
Views: 449
|
Forum: Model-A
05-22-2024, 11:37 PM
|
Replies: 7
Views: 1,091
|
Forum: Model A (1928-31)
05-21-2024, 06:08 PM
|
Replies: 21
Views: 979
Re: Squeal that I can’t pinpoint
I think most of the comments are looking at this incorrectly. The OP describes it as a belt like squeal that goes away when the clutch is pressed. The throw out bearing spins when the clutch is...
|
Forum: Model A (1928-31)
05-19-2024, 11:32 PM
|
Replies: 7
Views: 548
Re: Eaton gas cap, original or aftermarket?
The direct answer, which is helpful in future searches of the forum:
The picture shows an original Eaton gas cap. This is because of the vent holes and a side profile would show a height of about...
|
Forum: Model A (1928-31)
05-19-2024, 11:27 AM
|
Replies: 51
Views: 2,561
Re: sign of the times
If you look, just about all new semi’s and other heavy duty trucks are automatics. Most on the road today are automatic. Some manufacturers like Kenworth, don’t even offer manual transmissions. I...
|
Forum: Model A (1928-31)
05-18-2024, 11:24 PM
|
Replies: 51
Views: 2,561
Re: sign of the times
I’m sure most people on here also complained when the rotary phone went away, flip phones were replaced by iPhones and so on.
How many on here have driven and know how to operate a PDK style...
|
Forum: Model A (1928-31)
05-16-2024, 12:28 AM
|
Replies: 17
Views: 837
Re: Fuse size
This is the true answer. You can estimate draw and load, but at the end of the day a shorted (grounded) wire will carry the supply load at a max load since the ground can handle it.
Go with 30...
|
Forum: Model A (1928-31)
05-16-2024, 12:24 AM
|
Replies: 17
Views: 837
Re: Fuse size
For a house, this is correct. Automotive applications don’t have a “code”.
|
Forum: Model A (1928-31)
05-16-2024, 12:20 AM
|
Replies: 11
Views: 673
|
Forum: Model A (1928-31)
05-03-2024, 06:13 PM
|
Replies: 41
Views: 4,048
|
Forum: Model A (1928-31)
05-02-2024, 11:07 AM
|
Replies: 5
Views: 659
Re: Shipping NOS axles
Stolen goods, usually cars and other large items that take a container to conceal and remove. It's quite common.
|
Forum: Model A (1928-31)
04-29-2024, 07:11 PM
|
Replies: 20
Views: 1,357
|
Forum: Model-A
04-26-2024, 09:54 PM
|
Replies: 3
Views: 606
|
Forum: Early V8
04-26-2024, 09:53 PM
|
Replies: 1
Views: 231
|
Forum: Early V8
04-26-2024, 09:53 PM
|
Replies: 2
Views: 177
|