Forum: Early V8 (1932-53)
Yesterday, 04:24 PM
|
Replies: 511
Views: 37,000
Re: 276 stroker from 35 years of parts
Gary
My shop instructor told us to put sealant only on the removable part to hold the gasket. Easier cleanup that way. That was over sixty years ago, don't know about today.
Bruce
|
Forum: Early V8 (1932-53)
06-09-2024, 08:24 PM
|
Replies: 15
Views: 616
|
Forum: Early V8 (1932-53)
05-26-2024, 09:34 AM
|
Replies: 22
Views: 995
|
Forum: Early V8 (1932-53)
05-24-2024, 07:58 PM
|
Replies: 10
Views: 404
|
Forum: Early V8 (1932-53)
03-31-2024, 09:50 AM
|
Replies: 11
Views: 909
|
Forum: Early V8 (1932-53)
03-17-2024, 08:34 PM
|
Replies: 22
Views: 1,584
|
Forum: Early V8 (1932-53)
03-17-2024, 06:19 PM
|
Replies: 20
Views: 1,742
|
Forum: Early V8 (1932-53)
03-11-2024, 08:11 PM
|
Replies: 14
Views: 1,214
|
Forum: Early V8 (1932-53)
03-04-2024, 10:15 AM
|
Replies: 4
Views: 507
|
Forum: Early V8 (1932-53)
03-03-2024, 10:50 PM
|
Replies: 21
Views: 1,635
|
Forum: Early V8 (1932-53)
03-03-2024, 10:38 PM
|
Replies: 14
Views: 2,140
|
Forum: Early V8 (1932-53)
02-06-2024, 08:57 PM
|
Replies: 24
Views: 1,904
|
Forum: Early V8 (1932-53)
01-16-2024, 12:16 PM
|
Replies: 21
Views: 1,292
Re: Clutch won’t release
WD40 is a water displacer not a lubricator. Spray some on a metal surface in the weather and see how long until it disappears.
Bruce
|
Forum: Early V8 (1932-53)
01-16-2024, 12:00 PM
|
Replies: 25
Views: 1,675
Re: 1950 Ford sedan seat too far forward
It sounds like you have the wrong seat in your car. As to tilt, try a 1/4 inch shim under the front two bolts to start, going to 3/8 if that helps. I would remove the seat, clean and lube...
|
Forum: Early V8 (1932-53)
01-11-2024, 08:57 PM
|
Replies: 206
Views: 18,549
Re: 47 V8 ignition mystery
Sitting in the drivers seat the right hand side is 1234, the left side is 5678 from front to back. The crab cap should be numbered. One wire at a time.
Bruce
|
Forum: Early V8 (1932-53)
01-11-2024, 08:31 PM
|
Replies: 19
Views: 1,113
|
Forum: Early V8 (1932-53)
01-11-2024, 06:46 PM
|
Replies: 31
Views: 1,974
|
Forum: Early V8 (1932-53)
01-11-2024, 06:36 PM
|
Replies: 25
Views: 1,970
|
Forum: Early V8 (1932-53)
01-10-2024, 09:01 PM
|
Replies: 25
Views: 1,970
|
Forum: Early V8 (1932-53)
01-10-2024, 08:43 PM
|
Replies: 31
Views: 1,974
|
Forum: Early V8 (1932-53)
01-07-2024, 09:01 PM
|
Replies: 14
Views: 1,273
|
Forum: Early V8 (1932-53)
12-22-2023, 09:45 PM
|
Replies: 13
Views: 984
Re: I broke a new ring.
Call Egge Machine next week. They will sell singles.
562 945 3419 They are in Santa Fe Springs, Ca. 90670
Bruce
|
Forum: Early V8 (1932-53)
12-21-2023, 09:02 PM
|
Replies: 35
Views: 2,794
Re: Violent shake.
I had the same issues in 1960 on my 50 Ford. I had the flywheel resurfaced. Should have had it balanced at the same time.
Bruce
|
Forum: Early V8 (1932-53)
12-07-2023, 09:31 PM
|
Replies: 79
Views: 5,373
|
Forum: Early V8 (1932-53)
12-02-2023, 11:42 AM
|
Replies: 19
Views: 1,623
|