Forum: Model A (1928-31)
04-25-2020, 11:37 AM
|
Replies: 2
Views: 1,141
|
Forum: Model A (1928-31)
04-25-2020, 11:05 AM
|
Replies: 2
Views: 1,141
headlight bar patch
Greetings to all and I hope you're all safe.
I am working on a 1931 fender that needs a patch panel where the headlight bar is attached. I have the patches and they have indentations in them...
|
Forum: Model A (1928-31)
01-15-2020, 04:55 PM
|
Replies: 39
Views: 6,957
|
Forum: Model A (1928-31)
01-02-2020, 11:00 AM
|
Replies: 4
Views: 1,424
Re: Need help with subrails
Thanks for the reply, rotorwrench. I did check out Vince Falter's site and he mentioned he had some drawings of the hole locations. If I could locate all of the holes first it would make it much...
|
Forum: Model A (1928-31)
01-02-2020, 08:54 AM
|
Replies: 4
Views: 1,424
Need help with subrails
Good morning, all.
I am in the process of putting my 1930 coupe back on the road after 40 years storage outside in Michigan. After removing the body I found that the subrails were MIA. I ordered a...
|
Forum: Model A (1928-31)
11-18-2018, 02:42 PM
|
Replies: 22
Views: 5,871
|
Forum: Model A (1928-31)
10-01-2016, 06:07 AM
|
Replies: 7
Views: 1,589
|
Forum: Model A (1928-31)
09-30-2016, 02:49 PM
|
Replies: 7
Views: 1,589
|
Forum: Model A (1928-31)
09-30-2016, 11:25 AM
|
Replies: 7
Views: 1,589
Another generator question
Hello, all.
I have a 1931 coupe, all stock that is giving me fits. The generator will not charge. It was charging just fine then all of a sudden quit. I am getting nothing from the output stud and...
|
Forum: Model A (1928-31)
03-23-2016, 06:54 PM
|
Replies: 27
Views: 5,343
|
Forum: Model A (1928-31)
03-07-2016, 08:15 AM
|
Replies: 2
Views: 1,307
Opinions on gaskets
I'm installing the transmission and bell housing on my '30 coupe and got to the outer u-joint covers (clamshell). I have both types of seals, cork and felt and wonder which type is best to use. Any...
|
Forum: Model A (1928-31)
02-05-2015, 05:58 AM
|
Replies: 10
Views: 2,342
Re: Removing a solid top
Thanks Brent, for taking the time to post those pictures. They are really helpful. I'm gonna remove the insert and post some pics.
Paul- I did consider just hiding the solid top, but there is a...
|
Forum: Model A (1928-31)
02-04-2015, 02:54 PM
|
Replies: 10
Views: 2,342
|
Forum: Model A (1928-31)
02-04-2015, 02:25 PM
|
Replies: 10
Views: 2,342
Re: Removing a solid top
Sorry, maybe used the wrong term. Coupe has cowl lamps and has the block and wiring for a dome lamp. Anyway, got into it a little today and melted away some lead. It's welded for an inch or so every...
|
Forum: Model A (1928-31)
02-04-2015, 07:11 AM
|
Replies: 10
Views: 2,342
Removing a solid top
Hi, all!
I'm in the process of restoring a 1930 special coupe. Problem is that someone in the past has installed a solid top. It is leaded in. Because of this, I can't separate the two body halves...
|
Forum: Model A (1928-31)
09-26-2014, 08:24 AM
|
Replies: 72
Views: 22,783
Re: Should light switch/horn rod turn with wheel
Depends on why the rod is turning. Could be a bind between the rod and the shaft. You can probably tell by rotating the light switch rod before installing the switch-it should turn loose and free. If...
|
Forum: Model A (1928-31)
04-21-2012, 05:24 PM
|
Replies: 36
Views: 7,331
|
Forum: Model A (1928-31)
02-16-2012, 09:34 AM
|
Replies: 20
Views: 5,714
Re: water leak in exh port
I know that most block repair/sealers suggest that the engine be run without the offending cylinder spark plug installed. Can anyone tell me how you can find out which cylinder (or where) the block...
|
Forum: Model A (1928-31)
08-31-2011, 07:08 PM
|
Replies: 13
Views: 2,186
Re: fan belt installation
The 25-20426 belt is one that I went to when I installed an alternator. The alternator pulley is significantly smaller in diameter than the generator pulley, and I had problems with the belt being...
|
Forum: Model A (1928-31)
04-29-2011, 06:57 PM
|
Replies: 17
Views: 7,997
|
Forum: Model A (1928-31)
04-23-2011, 01:59 PM
|
Replies: 31
Views: 7,850
|
Forum: Model A (1928-31)
04-11-2011, 06:38 PM
|
Replies: 14
Views: 2,420
Re: Frt. end wobble
I agree with Brent.. betcha the ball on the pitman arm looks like a football instead of a basketball.
|
Forum: Model A (1928-31)
03-28-2011, 09:34 PM
|
Replies: 7
Views: 2,079
Re: L-B Material Shortage
But.... with as much $$$$$ as they charge for their kits, the proper thing to do would be to say "I'll check with my supplier and get back to you".
Sheesh... customer service sure goes south when...
|
Forum: Model A (1928-31)
03-28-2011, 12:09 PM
|
Replies: 28
Views: 6,693
|
Forum: Model A (1928-31)
03-27-2011, 06:57 PM
|
Replies: 4
Views: 1,443
|