Forum: Early V8
04-04-2024, 10:00 PM
|
Replies: 0
Views: 146
|
Forum: Early V8
05-20-2023, 06:44 PM
|
Replies: 0
Views: 301
1940 top radiator tank
Need a good top tank off a 1940 radiator in good condition I have some with dents and bad water outlets . Thanks
|
Forum: Early V8
02-17-2023, 11:39 PM
|
Replies: 2
Views: 647
|
Forum: Early V8
02-10-2023, 08:42 PM
|
Replies: 2
Views: 647
|
Forum: Early V8
02-05-2023, 09:23 PM
|
Replies: 2
Views: 647
|
Forum: Early V8
02-02-2023, 11:27 PM
|
Replies: 0
Views: 396
|
Forum: Early V8
12-12-2022, 12:35 AM
|
Replies: 0
Views: 302
|
Forum: Early V8
07-04-2022, 07:13 PM
|
Replies: 0
Views: 516
|
Forum: Early V8
03-11-2022, 09:54 PM
|
Replies: 1
Views: 495
|
Forum: Early V8
01-20-2022, 07:38 PM
|
Replies: 1
Views: 495
1940 Ford Pickup Rear bumper New
This 40 pickup rear bumper is new and still in the orginial packing . Never installed . If you are in the USA I will ship to your door for 435.00 . Thanks
|
Forum: Early V8 (1932-53)
11-19-2021, 06:42 PM
|
Replies: 17
Views: 2,852
Re: Condensers
Bored & Stroked Thanks for your information . Much appreciated . I have a couple of the secondary plates for parts and they are new but one has the lugs where you said and the other has the lugs on...
|
Forum: Early V8 (1932-53)
11-19-2021, 01:47 AM
|
Replies: 17
Views: 2,852
Re: Condensers
Bored & Stroked I was lucky to find three of the Harmon Collins Distributors NOS plus parts for them years ago. You are correct , there is a difference in the secondary plates . Which one gives the...
|
Forum: Early V8 (1932-53)
11-16-2021, 08:22 PM
|
Replies: 17
Views: 2,852
|
Forum: Early V8 (1932-53)
11-14-2021, 05:58 PM
|
Replies: 17
Views: 2,852
Condensers
I need a couple of good condensers for a Harmon Collins Dist. The last ones I got were from Jim at Bubbas Any body know where to go . Thanks
|
Forum: Early V8 (1932-53)
08-31-2021, 06:06 PM
|
Replies: 9
Views: 1,282
Re: Ash tray 40-41 Pickup.
alanwoodieman I have the raised dash with the ford script . It loos like the ashtray would have gone in the hole and had a flip top on it.
|
Forum: Early V8 (1932-53)
08-29-2021, 06:25 PM
|
Replies: 2
Views: 520
|
Forum: Early V8 (1932-53)
08-29-2021, 06:14 PM
|
Replies: 9
Views: 1,282
Ash tray 40-41 Pickup.
I just started a rebuild on a 40-41 pickup cab . I had the cab and doors blasted . Going to make a shop truck. In the middle of the dash up at the top just down from the window moldings there is a...
|
Forum: Model T (1909-1927)
03-09-2021, 08:21 PM
|
Replies: 1
Views: 1,381
American Vintage Rims
Guys i need some information on Mark Mc Laren at American Vintage Rims . Is he still in business? I have tried to get in touch with him for some rims . Thanks !
|
Forum: Early V8 (1932-53)
02-02-2021, 11:19 PM
|
Replies: 7
Views: 1,298
|
Forum: Early V8 (1932-53)
12-21-2020, 12:34 AM
|
Replies: 22
Views: 4,117
Re: Brassworks radiators
They are super people to do business with. I have two of their radiators and they are spot on in looks and fit. Nice Truck !!
|
Forum: Early V8 (1932-53)
04-28-2020, 10:25 PM
|
Replies: 23
Views: 4,021
|
Forum: Early V8 (1932-53)
04-28-2020, 10:17 PM
|
Replies: 20
Views: 4,118
Re: Oil slinger, crank snout, crank sleeve.
You need to keep the oil slinger . Once you install your crank pulley and the bolt and washer that holds it on it will hold the oil slinger in place tight against the crank gear.
|
Forum: Early V8 (1932-53)
04-19-2020, 09:01 PM
|
Replies: 18
Views: 3,401
Re: Headers
I have two original sets of Fenton headers . Both sets have the ford part numbers. I would take the photos but they are on my cars . The numbers are the same as the photos above.
|
Forum: Early V8 (1932-53)
03-06-2020, 12:04 AM
|
Replies: 39
Views: 6,288
Re: Mig wire type
Any mig wire you buy you won't be able to metal finish the weld. Either tig or gas welding will work .
|
Forum: Early V8 (1932-53)
02-17-2020, 09:51 PM
|
Replies: 69
Views: 10,490
Re: I guess its time ???
Jim I want to thank you for timing all of the Harmon Collins crabs I sent you .They are going strong .I wish you the best with your health. Take it easy .
|