Forum: Model T (1909-1927)
05-27-2023, 08:33 PM
|
Replies: 13
Views: 2,291
Re: Need help Identifying
Warford over drive, direct drive and under drive. Two speed rearend ? Photo of the underside behind the transmission and also the rear end. Then we can tell you what you have.
|
Forum: Model T (1909-1927)
05-27-2023, 08:28 PM
|
Replies: 5
Views: 1,052
|
Forum: Early V8 (1932-53)
02-28-2023, 08:23 PM
|
Replies: 3
Views: 580
rod bearings
Are the full floating bearings for the rods the same from 39 trough 48?
|
Forum: Model-T
09-22-2022, 06:03 PM
|
Replies: 2
Views: 1,742
|
Forum: Early V8 (1932-53)
09-15-2022, 07:05 PM
|
Replies: 31
Views: 6,095
Re: charley
I must SAY I have been friends with this fine man for many years. He is a true gentleman, beyond any question! I have been doped with spell check more than several times. Charlie does not have a...
|
Forum: Early V8 (1932-53)
09-15-2022, 09:21 AM
|
Replies: 31
Views: 6,095
Re: charley
I always appreciated Charlie's knowledge and willingness to help others. I don't understand why he is gone. I don't think he died. Please tell me what's going on here!
|
Forum: Early V8 (1932-53)
09-02-2022, 07:33 AM
|
Replies: 7
Views: 1,529
Re: Holly 94 carburetors new information
Where did you get the power valves that were leakers? The ones I have gotten from Datona have been good. I have five carburetors with them so far without any problems.
|
Forum: Model-T
09-01-2022, 06:18 PM
|
Replies: 2
Views: 1,742
|
Forum: Early V8 (1932-53)
09-01-2022, 05:04 PM
|
Replies: 5
Views: 804
|
Forum: Early V8 (1932-53)
09-01-2022, 03:52 PM
|
Replies: 5
Views: 804
New style float valves
I’m posting just for an informative note. These replace needle seat valves for many carburetor applications. They are made for ethanol fuel. I’m using them in three applications and feel like they...
|
Forum: Early V8 (1932-53)
08-31-2022, 08:43 PM
|
Replies: 11
Views: 1,852
Re: Brake question
Arcing shoes is good but, on the brakes, you're using there's no way to adjust the bottom of the shoes the bottom anchors are fixed. what your experiencing is the shoes barely touching the drum. I...
|
Forum: Early V8 (1932-53)
08-31-2022, 06:03 PM
|
Replies: 7
Views: 1,529
Holly 94 carburetors new information
I’ve been rebuilding carburetors most of my adult life. I’m not going to claim that I’m an expert. However my carb’s work well and run very good. Over the past few years I rebuilt several Holly 94s...
|
Forum: Model-T
08-21-2022, 05:25 PM
|
Replies: 2
Views: 1,742
1923 T depot hack
FOR SALE 1923 MOTEL T FORD DEPOT HACK. this was an older restoration that came out of long storage and was gone through, with many refreshed components. Super nice powder coated wire wheels, new...
|
Forum: Early V8 (1932-53)
08-21-2022, 10:10 AM
|
Replies: 23
Views: 3,124
|
Forum: Early V8 (1932-53)
05-05-2022, 06:50 AM
|
Replies: 14
Views: 1,957
Re: Rhinebeck car and swap meet
I’ve been told that they’ll open the gates at eight you could shut up and officially starts at noon but I’d be imagining that there’s probably a lot that goes on prior to that I know I’ve had a good...
|
Forum: Early V8 (1932-53)
05-04-2022, 08:32 PM
|
Replies: 14
Views: 1,957
|
Forum: Model T (1909-1927)
04-28-2022, 08:44 PM
|
Replies: 19
Views: 3,572
|
Forum: Early V8 (1932-53)
04-21-2022, 07:48 PM
|
Replies: 298
Views: 43,076
|
Forum: Early V8 (1932-53)
02-26-2022, 07:17 PM
|
Replies: 5
Views: 633
|
Forum: Early V8 (1932-53)
02-26-2022, 08:23 AM
|
Replies: 5
Views: 758
Re: identify a 50 block
Thanks it's a factory relieved block, I thought the C possibly meant made in Canada ? I have three other 50 blocks and none of them have that prefix and number on them. 59A block does not have that...
|
Forum: Early V8 (1932-53)
02-26-2022, 08:17 AM
|
Replies: 34
Views: 2,680
Re: Why I built a Flathead
If you decide to put it into an earlier v8 car or truck, you need to change the pan to a truck pan. very hard to find a good one. I have a good truck pan that I would sell , they are in very short...
|
Forum: Early V8 (1932-53)
02-25-2022, 09:37 PM
|
Replies: 2,253
Views: 384,228
Re: 1932 The Deuce, Dually, Dump Truck
Great find. the recommended 50% acetone and Marvel Midstory oil. soak it be patient it will take quite a while. I just freed up a flathead sitting for 56 years.
|
Forum: Early V8 (1932-53)
02-25-2022, 09:12 PM
|
Replies: 5
Views: 758
identify a 50 block
I'm building a 59-engine bored .100 with a 4" stroke Scat crank. I noticed the block is factory relieved. I think it was a truck block. I also found this number cast into the block. I have never seen...
|
Forum: Early V8 (1932-53)
08-12-2021, 10:03 AM
|
Replies: 17
Views: 1,786
|
Forum: Early V8 (1932-53)
08-02-2021, 10:06 PM
|
Replies: 10
Views: 1,959
Re: 1939 engine transplant to an 8ba
i have a 39 PU barrel nose with a 59AB engine With double pulley set up . However trying to put the 8BA in a 39 standard coupe. Wonder if the double pulley would work as I have that set up in my...
|