Forum: Model A (1928-31)
04-26-2024, 09:47 AM
|
|
Replies: 11
Views: 1,047
|
|
Forum: Model A (1928-31)
04-12-2024, 04:02 PM
|
|
Replies: 7
Views: 552
|
|
Forum: Model A (1928-31)
04-09-2024, 09:40 AM
|
|
Replies: 7
Views: 552
|
|
Forum: Model A (1928-31)
04-02-2024, 04:25 PM
|
|
Replies: 2
Views: 559
Model a Ford Transmission
I put a transmission in my 1931 Ford Pickup figuring it would be more quite. The gears looked good also. When I took it for a drive it locked in high gear. I figure it to be in the shifter top. Any...
|
|
Forum: Model A (1928-31)
02-26-2024, 05:28 PM
|
|
Replies: 16
Views: 1,045
|
|
Forum: Model A (1928-31)
02-25-2024, 06:46 PM
|
|
Replies: 16
Views: 1,045
|
|
Forum: Model A (1928-31)
02-25-2024, 06:42 PM
|
|
Replies: 34
Views: 1,920
Re: Rotor position at TDC
Some of the cam gears don't have a very deep dimple. After I locate the dimple I use a small mirror and flashlight to see if the dimple is perfectly in line with the pin hole.
Alway's remember to...
|
|
Forum: Model A (1928-31)
02-09-2024, 10:37 AM
|
|
Replies: 20
Views: 1,560
|
|
Forum: Model A (1928-31)
01-16-2024, 03:06 PM
|
|
Replies: 57
Views: 23,616
Re: Toe-in Adj. tool
This is the one I made. I use two straight pins pushed in the tread, set the pointer on the toe in fixture, push the car forward so the pins are on the front side of the tire, move the toe in fixture...
|
|
Forum: Model A (1928-31)
06-29-2023, 06:16 PM
|
|
Replies: 16
Views: 1,928
Re: Fan Belt replacement
Pull the bolt that holds the generator on, slip the belt into the pulley, you can then work the bolt back in to mount the generator. Then set the tension, not tight but not loose. To tight causes...
|
|
Forum: Model A (1928-31)
03-30-2023, 05:32 PM
|
|
Replies: 30
Views: 7,273
|
|
Forum: Model A (1928-31)
03-11-2023, 11:16 AM
|
|
Replies: 11
Views: 2,188
|
|
Forum: Model A (1928-31)
03-04-2023, 03:33 PM
|
|
Replies: 46
Views: 8,035
|
|
Forum: Model A (1928-31)
02-20-2023, 04:37 PM
|
|
Replies: 19
Views: 3,858
|
|
Forum: Model A (1928-31)
01-08-2023, 04:41 PM
|
|
Replies: 44
Views: 8,809
|
|
Forum: Model A (1928-31)
10-31-2022, 07:19 AM
|
|
Replies: 7
Views: 950
Re: 1930 Murray Exterior Door Key
I had a ignition lock with the A**** number and took it to a lock shop and they looked it up on their cards and made me a key right away. Try a lock shop and you should have success.
|
|
Forum: Model A (1928-31)
10-28-2022, 09:59 AM
|
|
Replies: 5
Views: 889
Reflections of Autumn
My Speedster sitting in the barn I noticed the reflection of the maple leaves on a tree approximately 300 feet across the road showing on my Speedster windshield. I think this is a once in a lifetime...
|
|
Forum: Model A (1928-31)
10-04-2022, 08:48 AM
|
|
Replies: 7
Views: 1,269
Re: Interior light wiring
Bill Cilker
My 31 Slant fordor is like your picture. I didn't have power to the dome light, had to loosen the panel that covers the header and part of the headliner to get to the connection that you...
|
|
Forum: Model A (1928-31)
10-03-2022, 09:05 AM
|
|
Replies: 41
Views: 6,555
|
|
Forum: Model A (1928-31)
10-02-2022, 04:19 PM
|
|
Replies: 41
Views: 6,555
Re: King Pin Reaming
PeteCruz2715, I have the same reamer driver as you. It appears that you didn't get the directions on how to use the reamer. Pictured are the directions. I have used this reamer on two of my Model A...
|
|
Forum: Model A (1928-31)
10-01-2022, 12:11 PM
|
|
Replies: 9
Views: 1,893
|
|
Forum: Model A (1928-31)
08-17-2022, 08:58 AM
|
|
Replies: 12
Views: 1,286
|
|
Forum: Model A (1928-31)
07-22-2022, 08:27 AM
|
|
Replies: 51
Views: 11,747
Re: toe in tool
This is the one I made. I use two straight pins pushed in the tread, set the pointer on the toe in fixture, push the car forward so the pins are on the front side of the tire, move the toe in fixture...
|
|
Forum: Model A (1928-31)
05-25-2022, 12:44 PM
|
|
Replies: 13
Views: 2,006
|
|
Forum: Model A (1928-31)
04-19-2022, 10:21 AM
|
|
Replies: 42
Views: 6,628
|
