Forum: Early V8 (1932-53)
Today, 01:55 PM
|
Replies: 11
Views: 29
Re: 39 synchronizer question
Does the synchro slide back & forth easily or does it take some effort and "clicks" into the forward and aft position?
|
Forum: Early V8 (1932-53)
Today, 01:35 PM
|
Replies: 11
Views: 29
Re: 39 synchronizer question
Can you tell us a little more? Is this trans out of a car and bought as working or rebuilt?
I'm curious what MacVP thinks? I'm assuming they are essential and help to keep the synchro hub in...
|
Forum: Early V8 (1932-53)
Today, 01:24 PM
|
Replies: 24
Views: 1,054
Re: Evans Aluminum Heads
So interesting enough, I just installed a brand new, from the box set of 1126's (Block letter version of the 1116's). I CC'd both heads and got 70cc's.
|
Forum: Early V8 (1932-53)
Today, 08:42 AM
|
Replies: 21
Views: 774
|
Forum: Early V8 (1932-53)
Yesterday, 09:26 AM
|
Replies: 15
Views: 574
|
Forum: Early V8 (1932-53)
05-31-2024, 09:55 PM
|
Replies: 15
Views: 574
|
Forum: Early V8 (1932-53)
05-31-2024, 02:25 PM
|
Replies: 15
Views: 574
|
Forum: Early V8 (1932-53)
05-31-2024, 11:36 AM
|
Replies: 15
Views: 574
|
Forum: Model A (1928-31)
05-31-2024, 11:33 AM
|
Replies: 8
Views: 486
Re: Cast fuel bowl leaking- round two
Need to thank 1crosscut for his suggestion. I really watched closely and it turned out the source of the leak was coming from the inside fuel line needing to be snugged up against the male nipple...
|
Forum: Early V8 (1932-53)
05-31-2024, 11:06 AM
|
Replies: 7
Views: 395
|
Forum: Early V8 (1932-53)
05-29-2024, 03:40 PM
|
Replies: 15
Views: 615
|
Forum: Early V8 (1932-53)
05-29-2024, 09:05 AM
|
Replies: 15
Views: 615
Re: Boling Brothers Brakes Question
I did the same thing. I used old fashioned stick chalk and scribbled on the pads. Keep working until all of the chalk was removed when brake was applied. It didn't take long with some 80 grit...
|
Forum: Early V8 (1932-53)
05-29-2024, 06:57 AM
|
Replies: 15
Views: 615
|
Forum: Model A (1928-31)
05-29-2024, 04:29 AM
|
Replies: 8
Views: 486
Re: Cast fuel bowl leaking- round two
Thanks, Dave. I'm fairly certain it's coming from there. I've done the paper towel dabbing trick and it always underneath the screw. It's small enough that it will "pool" up for a bit on the flat...
|
Forum: Model A (1928-31)
05-28-2024, 08:49 PM
|
Replies: 8
Views: 486
Cast fuel bowl leaking- round two
OK, so I posted a while back about my weeping/leaking cast fuel bowl for a '28 roadster. I recent took it off, ground the internal vertical seat that the drain needle seats in with a stone, found a...
|
Forum: Early V8 (1932-53)
05-28-2024, 06:36 PM
|
Replies: 26
Views: 826
|
Forum: Early V8 (1932-53)
05-28-2024, 06:36 PM
|
Replies: 26
Views: 826
Re: Pictures after head swap (hot rod content)
Thank you, GB. I'll post some full car shot in a bit. Warning, it's an old hot rod and may have the worst fuel efficiency of any car I've owned. I've calculate 12-14 mph. It could be because...
|
Forum: Early V8 (1932-53)
05-28-2024, 06:34 PM
|
Replies: 26
Views: 826
|
Forum: Early V8 (1932-53)
05-28-2024, 11:07 AM
|
Replies: 26
Views: 826
|
Forum: Early V8 (1932-53)
05-28-2024, 09:34 AM
|
Replies: 26
Views: 826
|
Forum: Early V8 (1932-53)
05-27-2024, 12:13 PM
|
Replies: 26
Views: 826
|
Forum: Early V8 (1932-53)
05-27-2024, 09:06 AM
|
Replies: 26
Views: 826
|
Forum: Early V8 (1932-53)
05-27-2024, 08:54 AM
|
Replies: 26
Views: 826
Re: Pictures after head swap (hot rod content)
Unfortunately, I did. The two casting "nubs" on the lower section of fins on each head weeped. I finally got them to stop with 2 doses of liquid glass, but it was still bugging me that it was...
|
Forum: Early V8 (1932-53)
05-27-2024, 08:51 AM
|
Replies: 26
Views: 826
|
Forum: Early V8 (1932-53)
05-27-2024, 08:18 AM
|
Replies: 26
Views: 826
|