Forum: Model A (1928-31)
04-26-2023, 06:54 PM
|
Replies: 16
Views: 2,196
Fuel tank strainer,screen?
What was the reason for a screen in the fuel tank filler neck on the Model A? The service bulletins on page 311 say the screen is not a strainer but a fire preventative device. How does the screen...
|
Forum: Early V8 (1932-53)
03-17-2023, 09:31 AM
|
Replies: 5
Views: 605
|
Forum: Early V8 (1932-53)
03-14-2023, 03:02 PM
|
Replies: 57
Views: 5,593
Re: 1953 eac mercury engine value
Just got back from looking at the engine its definitely a Merc, standard bore,i cleaned the areas around the valves to bores and could not see any cracks on each bank, it rotates and every thing...
|
Forum: Early V8 (1932-53)
03-14-2023, 11:48 AM
|
Replies: 57
Views: 5,593
|
Forum: Early V8 (1932-53)
03-14-2023, 11:11 AM
|
Replies: 57
Views: 5,593
|
Forum: Early V8 (1932-53)
03-14-2023, 11:02 AM
|
Replies: 57
Views: 5,593
|
Forum: Early V8 (1932-53)
03-14-2023, 10:00 AM
|
Replies: 57
Views: 5,593
1953 eac mercury engine value
I am looking at buying a complete core EAC engine for a project. The engine is a take out from a 1952 f-1 with a heavy duty 4 speed bolted to it. It is complete from fan to u-joint with merc carb....
|
Forum: Early V8 (1932-53)
02-09-2023, 04:23 PM
|
Replies: 2
Views: 545
Re: 1935 Tudor Rear Seat Armrest Removal
Remove the window garnish moulding and all attaching screws, then lift straight up and the panel will come off. The back side of the arm rest has a hook plate that is screwed to the arm rest. The...
|
Forum: Early V8 (1932-53)
02-08-2023, 08:18 PM
|
Replies: 16
Views: 1,871
Re: Lubricating fan?
http://www.vanpeltsales.com/FH_web/flathead_oilfilledfan-servicetips.htm
LINK FROM VAN PELT ON HOW TO SERVICE FAN.
|
Forum: Early V8 (1932-53)
02-03-2023, 07:37 PM
|
Replies: 3
Views: 810
|
Forum: Early V8 (1932-53)
02-03-2023, 06:54 PM
|
Replies: 3
Views: 810
1940 rear axle pinion backlash
I have a question on how to adjust pinion backlash between the ring gear and pinion... do you INCREASE or DECREASE the driver side or passenger side gaskets to move the ring gear closer to pinion to...
|
Forum: Early V8 (1932-53)
01-19-2023, 05:55 PM
|
Replies: 4
Views: 1,135
Re: holley 94 discharge stuck!
THANK YOU!!! I center punched and drilled using a #37 drill about 1/8 inch deep. I then used a small slide hammer with a sheet metal screw on the end and it pulled right out. Thank you for all the...
|
Forum: Early V8 (1932-53)
01-19-2023, 12:28 PM
|
Replies: 4
Views: 1,135
holley 94 discharge stuck!
Anyone every removed a stuck Holley 94 brass pump discharge valve, it sits below the pump discharge nozzle? Tearing down this carb for a rebuild and the brass valve is stuck in the well. I tried...
|
Forum: Model A (1928-31)
01-16-2023, 04:16 PM
|
Replies: 15
Views: 2,166
Re: Dash light always on
The dash light on 30-31 has a switch built in to the light... a little nurled shaft that you flip up or down to turn on-off the light.
|
Forum: Model-A
12-28-2022, 10:52 AM
|
Replies: 1
Views: 941
|
Forum: Model A (1928-31)
12-17-2022, 01:19 PM
|
Replies: 30
Views: 6,723
Re: What is the best quality ignition points?
Has anyone used the NU-REX upper plate with their NU-REX brand of modern points? They claim to have the best points on the market, points number NN-53 for $9.75 and condenser NN-54 for $9.95. I have...
|
Forum: Early V8 (1932-53)
12-16-2022, 11:01 AM
|
Replies: 38
Views: 6,271
Re: chevy dizzy for flatheads
Could a Pertronix igniter be used in one of Charlie NY converted Chevy distributers if it has been built with points & condenser? I have one from many years ago and was wondering if its just a simple...
|
Forum: Model A (1928-31)
12-14-2022, 07:14 PM
|
Replies: 3
Views: 918
PHAETON top iron and bow question
Can anyone tell me what type of material Ford used on the radius part of the top bows? It appears to be fibrous material almost like leather. What can be used as a replacement material? Thank you.
|
Forum: Model A (1928-31)
12-11-2022, 05:57 PM
|
Replies: 7
Views: 1,792
|
Forum: Model A (1928-31)
12-11-2022, 12:01 AM
|
Replies: 7
Views: 1,792
Zenith carb. Adjusting needle seat
I am in the process of assembling a Zenith carburetor that uses a removable brass seat and I need to know if a fiber gasket is used under the brass seat. I have read some rebuild articles and most...
|
Forum: Model A (1928-31)
11-26-2022, 12:25 PM
|
Replies: 8
Views: 1,779
|
Forum: Model A (1928-31)
10-02-2022, 08:52 AM
|
Replies: 4
Views: 689
|
Forum: Model A (1928-31)
10-01-2022, 05:42 PM
|
Replies: 4
Views: 689
1928-29 phaeton front lap belts
Does anyone have pictures or advice on installing front lap belts in a phaeton? Where is the best place to mount the belts? The rear sub frame under the back portion of the seat is not acessable...
|
Forum: Model-A
09-17-2022, 10:14 AM
|
Replies: 1
Views: 941
|
Forum: Early V8 (1932-53)
09-04-2022, 04:06 PM
|
Replies: 81
Views: 11,236
|