Sympathy pains for Old Henry My 53 215" six decided to join Old Henry. Recently a nasty knock developed in the bottom end at the front of the engine. So it is time to dive in and see what is up. Getting this far was my Saturday project.
http://i962.photobucket.com/albums/a...ps54593348.jpg The head was pulled last week and taken to a machine shop. It showed receding seats and loose valve guides. Most likely the cause of intermittent skip/misfire I've been chasing for a while. The cylinders still look good. Crosshatch pattern is still visible and almost no ridge. Tomorrow I'll get a look at the crank. |
Re: Sympathy pains for Old Henry Did the 6'ers have hardened seats back then?
|
Re: Sympathy pains for Old Henry Chuck, sorry to hear about this latest problem with the sedan delivery. Keep us posted on what you find wrong with the lower end.
|
Re: Sympathy pains for Old Henry Sorry about that & as JM said keep us posted & keep the pictures coming also.
|
Re: Sympathy pains for Old Henry Chuck,Ah the joys of owning old cars.Phil
|
Re: Sympathy pains for Old Henry Ross, No hardened seats in this one. So i'm guessing the 215" run didn't.
Phil, That's why we have them. Always fun to be had Fixin' and Drivin'. |
Re: Sympathy pains for Old Henry I took a six cyl. from a '53 Ford in the '80's and installed a head from a diesel tractor for a friend and we put it in a Ford Dexta tractor. Everything bolted right on. it ran good for about a week! Then, Phhht! Never looked to see what came apart. As far as I know, it is still sitting in a field.
|
Re: Sympathy pains for Old Henry Chuck, Perfect time to drop in a v8 of some kind. You know me aways gotta mess with them. Good luck with it, yell if you need anything, Chuck S.
PS: FLATHEADS FOR EVER!! |
Re: Sympathy pains for Old Henry Chuck, I can relate... Been there, done that, several times...:eek: Just remember to HAVE FUN:D;)
|
Re: Sympathy pains for Old Henry Quote:
|
Re: Sympathy pains for Old Henry Chuck:
If you need a hand Let me know, as you know Grease is my friend. |
Re: Sympathy pains for Old Henry For 41ford1 - Might be apples and oranges here (Ford vs Chebbie) but back in the 80's I had a '66 Chebbie Nova w/ straight six developed a know. After spending a weekend underneath replacing all the rod bearing with no fix it turned out to be a broken tooth the timing gear causing the knocking noise.
|
Re: Sympathy pains for Old Henry Thanks for the sympathy.
I'm looking forward to seeing if you have a bearing problem like I have. Hope you're having fun driving. :) |
Re: Sympathy pains for Old Henry We always install hardened seats in rebuilds. Most old engines have had several regrinds of seats, leaving no room for another.
|
Re: Sympathy pains for Old Henry Tore in to it today. Plastigauged the rods and mains. Both show .002" to .0025". End play is at .008". All bearings and journal surfaces look decent. everything at the crank is at the high end of spec. I don't think any thing here is the source of the knock. Pistons are another story. They are running .010" to .022" smaller than the bores. The bores are good no scores, just what looks like normal wear. Crosshatching is still visible in the ring area. I had change the timing chain and gears in the spring of '12. They look OK. Right now I'm thinking piston slap is the source of the knock. It was the loudest when the engine was fully up to temp.
http://i962.photobucket.com/albums/a...psa3d8c559.jpg http://i962.photobucket.com/albums/a...ps92660324.jpg http://i962.photobucket.com/albums/a...ps1025420a.jpg http://i962.photobucket.com/albums/a...ps73e9bac6.jpg http://i962.photobucket.com/albums/a...ps68abfb9c.jpg Guys, I've finally come to the conclusion that this stuff is heavy and I am no longer 16. But that aint gonna stop me! |
Re: Sympathy pains for Old Henry Look at the rings and see if the butt ends are front to back. Some times off location you get piston slap. Also if this is and engine that needs over size valves stems.
I had a 200 6 in a 67 falcon put just new valves and run for years. |
Re: Sympathy pains for Old Henry Quote:
Quote:
|
Re: Sympathy pains for Old Henry Chuck,Normally piston slap quiets as the engine warms up due to the alum. Pistons expanding at a faster rate than the cast iron block.wrist pin s do the opposite. Phil
|
Re: Sympathy pains for Old Henry Quote:
|
Re: Sympathy pains for Old Henry Is the bore over or the piston under in No. 1 cylinder? What does the cylinder wall finish look like in No. 1? How is the fitup of rod bushings to piston pins and pins in pistons? The bearings and journals on crankshaft do look nice in your pictures.
|
All times are GMT -5. The time now is 09:14 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.